Manual Navman Wind 3100 (page 13 of 18) (English)

512545

13

Zoom out

Zoom in

Previous page

1/18

Next page

13

WIND 3100 Installation and Operation Manual

NAVMAN

Correct installation is critical to the performance of

the unit. It is vital to read this section of the manual

and the documentation that comes with the other

parts before starting installation.

The WIND 3100 can:

Drive external beepers or lights for the alarm.

Send and receive data from other NAVMAN

instruments connected via NavBus. Settings

for alarms, units, calibration and backlighting

are shared (see section 6-1).

Send and receive NMEA data to and from other

instruments (see section 6-2).

Warnings

The unit is waterproof from the front. Protect the rear

of the unit from water, or else water might enter the

breathing hole and damage the unit. The warranty

does not cover damage caused by moisture or water

entering the back of the unit.

The cable up the mast to the masthead unit must

run in conduit.

8-1 Installation

WIND 3100 display unit

1 Choose a location for the display unit that is:

Easily seen and protected from damage.

At least 100 mm from a compass and at

least 500 mm from a radio or radar

antenna.

Away from engines, fluorescent lights, and

power inverters.

Accessible from behind; the minimum

clearance required at the back is 50 mm

(2") (see mounting diagram).

With the back of the unit protected from

moisture.

2 The unit must mount on a flat panel which is

less than 20 mm (0.75") thick. Stick the

mounting template in place. Drill a 50 mm (2")

fixing hole through the centre hole in the

template. Note that the template allows space

around the unit for the protective cover.

3 Remove the fixing nut from the back of the unit.

Insert the stud at the back of the unit through the

mounting hole. Hand tighten the fixing nut.

8 Installation and setup

Masthead unit

Plan the installation. Read through these instructions

before you install the masthead unit and plan where

you will fit the mounting block and where you will

drill the cable holes in the mast. It is usually easiest

to install the masthead unit when the rig is off the

boat.

1 The mounting block is at one end of the 30 m

(90 ft) masthead cable. Fit the mounting block

on top of the mast:

With the base of the block horizontal.

With the fitting for the masthead arm facing

forward, parallel to the centre line to within

a few degrees (if the arm does not face

exactly forward, the wind direction will need

to be aligned, see section 3-4).

Use the self-tapping screws provided.

Cables Clearance

50 mm (2") minimum

20 mm (0.75")

maximum thickness

Fixing nut

Display

unit

Fixing hole

50 mm (2")

Side view of display unit mounting:

Ensure that any holes that you cut will not

weaken the boat or the mast. If in doubt,

consult a qualified boat builder or marine

engineer.

Arm faces forward

2 Drill an 8 mm (5/16") hole at the top of the

mast close to the mounting block for the cable

to enter the mast. Do not install the masthead

cable yet.

3 Drill an 8 mm (5/16") hole at the bottom of the

mast at a convenient place for the cable to exit

the mast. You will fit the cable junction box

close to this hole; it should be in a dry place

and not in the bilge.

4 Calculate how long the cable from the

masthead mounting block to the cable junction

Forward

Cables

1

Önskar svar till. sven.ahlm@gmail.com önskar beställa en ny komplett givarearm till navman wind 3100s , ser inte var jag kan göra detta och vad den skulle kosta mvh Submitted on 15-8-2021 at 18:00
Reply Report abuse
Behöver en ny givarearm , komplett, till navman 3100s wind, ser inte var jag kan beställa, och vad den kostar mvh Sven Ahlm Submitted on 15-8-2021 at 17:53
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

Register

Register getting emails for Navman Wind 3100 at:

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Navman Wind 3100 in the language / languages: English as an attachment in your email.

The manual is 0,27 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Navman Wind 3100

Navman Wind 3100 User Manual - German, Dutch, Italian, Swedish, Finnish - 75 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info