28502
63
Zoom out
Zoom in
Previous page
1/88
Next page
TRACKFISH 6500 Installation and Operation Manual 63
NAVMAN
Clear Used
Select Clear used to set Used (the amount
of fuel used) to zero. Do this to start measuring
the amount of fuel used over a certain time or
distance.
Tank size
Enter the capacity of the fuel tank. Navman
recommends measuring tank size by draining
the fuel tank, filling it to capacity and using the
fuel dispenser’s reading. Beware of air pockets,
especially in underfloor tanks.
Num. engines
Set the number of engines to 0, 1 or 2. If 0 is
selected the fuel features are turned off.
Calibrate
SmartCraft fuel sensors and Navman diesel
sensors are factory calibrated and should
never need recalibrating. Calibrating Navman
petrol/gasoline sensors gives more accurate
fuel values.
Twin engine installations require each fuel
transducer to be calibrated. This can be done
at the same time with two portable tanks or at
different times using one portable tank.
Calibrating the fuel transducer(s) requires
accurate measurement of the fuel
consumption. This is best done using a small
portable tank. At least 4 gallons (15 litres) of
fuel should be used to ensure an accurate
calibration.
It is often very difficult to fill underfloor tanks
to the same level twice due to air pockets, so
the more fuel used, the more accurate the
calibration.
To calibrate the fuel transducer(s), perform the
following steps:
1. Record the level of the fuel in the tank(s).
2. Connect the portable tank(s) to the engine
through the fuel transducer(s).
3. Run the engine at normal cruising speed
until at least 4 gallons (15 litres) of fuel has
been used per engine.
4. Check the actual amount of fuel used per
engine by refilling the portable tank(s) to
the original level and noting the reading(s)
from the fuel dispenser’s gauge.
5. Select Fuel. Use the cursor keys to change
the reading for each engine to match that
on the fuel dispenser’s gauge.
6. Press when the reading is correct.
Note: If the fuel calibration options appear
to give erroneous readings after a while,
first check that the fuel sensor has been
installed correctly according to the installation
instructions supplied with it, then see
Appendix B - Troubleshooting.
Flow filter
Most engines do not draw fuel from the tank at
a steady rate. To give a stable fuel flow reading,
the TRACKFISH calculates the flow value(s) by
taking several measurements and averaging
them. Use the Flow filter to set the period over
which the fuel flow is averaged.
The Flow filter can be set from 0 to 30
seconds. Use the lowest value which gives a
stable flow. Usually a value of 5 to 10 seconds
will give a satisfactory result for two-stroke
carburettor engines. Fuel injected or four-
stroke engines may require a larger value.
This setting affects the Fuel flow and Fuel
economy reading on the Fuel display but it
does not affect the Fuel used reading.
Fuel consumption curve
See section 12-3.
Diesel sensors
If the boat has twin diesel engines and Navman
diesel sensors, set up the diesel sensors:
1 In the fuel setup menu, select Diesel
sensors.
63


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Navman TRACKFISH_6500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Navman TRACKFISH_6500 in the language / languages: English as an attachment in your email.

The manual is 2,78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Navman TRACKFISH_6500

Navman TRACKFISH_6500 User Manual - German - 88 pages

Navman TRACKFISH_6500 User Manual - Dutch - 88 pages

Navman TRACKFISH_6500 User Manual - French - 89 pages

Navman TRACKFISH_6500 User Manual - Italian - 90 pages

Navman TRACKFISH_6500 User Manual - Swedish - 87 pages

Navman TRACKFISH_6500 User Manual - Spanish - 91 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info