512562
14
Zoom out
Zoom in
Previous page
1/42
Next page
14
TRACKER 5100/5100i/5500/5500i Installation and Operation Manual
NAVMAN
3-2 Distance and bearing calculator
The distance and bearing calculator can plot a course
of one or several legs and to show the bearing and length
of each leg, as well as the total distance along the course.
The completed course can be converted into a route.
To use the distance and bearing calculator:
1 Press ESC until the chart display is displayed.
Press MENU and select Distance.
2 Move the cursor to the start of the first leg. It
does not matter if this point is a waypoint or
not. Press ENT.
3 To add a leg to the course, move the cursor to
the end of the leg. It does not matter if this
point is a waypoint or not. The display shows
4 To change the data display:
i Select Data setup.
ii Change a data field:
a Press the cursor keys to highlight the
field.
b Press ENT to display a menu of the
data that can be shown in the field.
c Select the data to show in the field;
select None to leave the field empty.
iii Repeat the above step to set the other data
fields. Press ESC.
Tip: If less than four lines are used, the
numeric data will take up less of the chart area.
5 To turn the compass display off or on:
i Select Compass.
ii Select Off or On.
6 Finally, press ESC to return to the chart display.
3-3 Goto
Goto is a simple way of navigating straight to one
point.
To start the Goto
1 Choose the point to go to:
To go to a waypoint or to any point on the
chart:
i Press ESC until the chart display is
displayed.
ii Move the cursor to the destination.
iii Press MENU and select Goto.
To go to a waypoint from the waypoints
display:
i Press DISP and select Waypoints.
ii Press
or to highlight the
destination waypoint.
iii Press MENU and select Goto.
Warning: Make sure the course does not pass
over land or dangerous waters.
2 The TRACKER starts navigating to the
destination (see section 2-7). The chart shows:
The destination point marked with a circle.
The boat’s plotted course to the
destination.
Two CDI lines, parallel to the boat’s plotted
course (see appendix C, CDI).
To cancel a Goto
1 Press ESC until the chart display is displayed.
2 Press MENU and select Cancel goto.
the bearing and length of the leg, as well as
the total distance along the course. Press ENT.
4 To remove the last leg from the course, press
MENU and select Remove.
5 Repeat the above two steps to enter the whole
course.
6 To save the new course as a route, press
MENU and select Save. This also saves any
new points on the course as new waypoints,
with default names. If necessary, edit the route
later (see section 10-2-2) and edit any new
waypoints later (see section 9-2-3).
7 Finally, press ESC to return to the chart display.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Navman Tracker 5500i at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Navman Tracker 5500i in the language / languages: English as an attachment in your email.

The manual is 0,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Navman Tracker 5500i

Navman Tracker 5500i User Manual - German - 43 pages

Navman Tracker 5500i User Manual - Dutch - 41 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info