512566

Navman Tracker 5430i Manual

14
Zoom out
Zoom in
Previous page
1/44
Next page
14
TRACKER 5430/5430i Installation and Operation Manual
NAVMAN
3-2 Distance and bearing calculator
The distance and bearing calculator can plot a
course of one or several legs and to show the
bearing and length of each leg, as well as the
total distance along the course. The completed
course can be converted into a route.
To use the distance and bearing calculator:
1 Press ESC until the chart display is displayed.
Press MENU and select Distance.
2 Move the cursor to the start of the first leg. It
does not matter if this point is a waypoint or
not. Press ENT.
3 To add a leg to the course, move the cursor
to the end of the leg. It does not matter if this
point is a waypoint or not. The display shows
3 To choose the size of the numbers:
i Select Size.
ii Select:
Small: displays three fields per line and
up to four lines.
Medium/Large: displays two fields per
line and up to four lines.
4 To change the data display:
i Select Data setup.
ii Change a data field:
a Press the cursor keys to highlight
the field.
3-3 Goto
Goto is a simple way of navigating straight to
one point.
To start the Goto
1 Choose the point to go to:
To go to a waypoint or to any point on the
chart:
i Press ESC until the chart display is
displayed.
ii Move the cursor to the destination.
iii Press MENU and select Goto.
To go to a waypoint from the waypoints
display:
i Press DISP and select Waypoints.
ii Press or to highlight the
destination waypoint.
iii Press MENU and select Goto.
Warning: Make sure the course does not
pass over land or dangerous waters.
2 The TRACKER starts navigating to the
destination (see section 2-7). The chart
shows:
The destination point marked with a
circle.
The boat’s plotted course to the
destination.
Two CDI lines, parallel to the boat’s
plotted course (see appendix C, CDI).
To cancel a Goto
1 Press ESC until the chart display is displayed.
2 Press MENU and select Cancel goto.
the bearing and length of the leg, as well
as the total distance along the course.
Press ENT.
4 To remove the last leg from the course, press
MENU and select Remove.
5 Repeat the above two steps to enter the
whole course.
6 To save the new course as a route, press
MENU and select Save. This also saves any
new points on the course as new waypoints,
with default names. If necessary, edit the
route later (see section 10-2-2) and edit any
new waypoints later (see section 9-2-3).
7 Finally, press ESC to return to the chart
display.
b Press ENT to display a menu of the
data that can be shown in the field.
c Select the data to show in the field;
select None to leave the field empty.
iii Repeat the above step to set the other
data fields. Press ESC.
Tip: If less than four lines are used,
the numeric data will take up less of the
chart area.
5 To turn the compass display off or on:
i Select Compass.
ii Select Off or On.
6 Finally, press ESC to return to the chart
display.
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Navman Tracker 5430i at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Navman Tracker 5430i in the language / languages: English as an attachment in your email.

The manual is 0,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Navman Tracker 5430i

Navman Tracker 5430i User Manual - German - 45 pages

Navman Tracker 5430i User Manual - Dutch - 45 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info