512548
8
Zoom out
Zoom in
Previous page
1/40
Next page
REPEAT 3100 Installation and Operation Manual
NAVMAN
8
5 Installation and setup
Clearance 50 mm
(2") minimum
20 mm (0.75")
maximum thickness
Fixing nut
Cables
Display
unit
Fixing hole
50 mm (2")
Side view of display unit mounting
5-1 Installation
REPEAT 3100 display unit
1 Choose a location for the display unit that is:
Easily seen and protected from damage.
At least 100 mm (4") from a compass and
at least 500 mm (1.65 ft) from a radio or
radar antenna.
Away from engines, fluorescent lights, and
power inverters.
Accessible from behind; the minimum
clearance required at the back is 50 mm
(2") (see right).
With the back of the unit protected from
moisture.
2 The unit must mount on a flat panel which is
less than 20 mm (0.75") thick. Stick the
mounting template in place. Drill a 50 mm (2")
fixing hole through the centre hole in the
template.
Note that the template allows space around
the unit for the protective cover.
3 Remove the fixing nut from the back of the unit.
Insert the stud at the back of the unit through
the mounting hole. Hand tighten the fixing nut.
Power/data cable wiring
Follow the wiring example on the next page:
1 The REPEAT 3100 requires 12 V DC power.
Fit a power switch and fuse to the power
supply or power the unit from a fused auxiliary
switch. The fuse should be 1 A for up to five
NAVMAN 3100 series instruments.
2 If the REPEAT 3100 is to receive data from
other instruments via the NavBus, install these
instruments and connect the REPEAT 3100 to
the NavBus.
Note: If an instrument can be connected to the
REPEAT 3100 by both NavBus and by NMEA,
then use the NavBus, because more
information can be shared via the NavBus (see
section 3-1).
Correct installation is critical to the performance of
the unit. It is vital to read this section of the manual
and the documentation that comes with the other
parts before starting installation.
Warnings
The unit is waterproof from the front. Protect the rear
of the unit from water, or else water might enter the
breathing hole and damage the unit. The warranty
does not cover damage caused by moisture or water
entering the back of the unit.
Ensure that any holes that you cut will not weaken
the boat’s structure. If in doubt, consult a qualified
boat builder.
3 If the REPEAT 3100 is to receive NMEA data
from other compatible instruments, install
these instruments and connect each
instrument’s NMEA output to one of the three
REPEAT 3100 NMEA inputs. Up to three
instruments can be connected.
4 Tape or cover any unused wires or connectors
to protect them from water and keep them from
shorting together.
Setup and test
Set up the unit as described in section 5-3.
Take the boat for a trial run to check that all the
instruments work correctly.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Navman Repeat 3100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Navman Repeat 3100 in the language / languages: English as an attachment in your email.

The manual is 0,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Navman Repeat 3100

Navman Repeat 3100 User Manual - German, Dutch, Italian, Swedish, Finnish - 64 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info