663849
26
Zoom out
Zoom in
Previous page
1/34
Next page
88 NAVMAN G-PILOT 3380 System - Installation
4 Inbetriebnahme nach Installation
1 Das G-PILOT 3380 System einschalten (siehe G-PILOT 3380 - Bedienung). Falls sich das Ruder bewegt,
sofort wieder ausschalten.
Wird auf AUTO geschaltet und der Ruder-Rückmelder ist noch nicht kalibriert, zeigt das G-PILOT 3380
System eine Fehlermeldung.
2 Wurde das G-PILOT 3380 System bereits vorher verwendet, sämtliche Anwender-Daten auf
Werkseinstellung zurücksetzen Das geschieht über die Menus Setup System > Werksrückstellung
> Beide (siehe das Buch PiILOT 3380 - Bedienung).
3 Die eingestellten Daten und Werte in die im Anhang vorhandene Anwenderdaten-Tabelle eintragen
(im Buch G-PILOT 3380 - Bedienung sind die Bedeutungen der einzelnen Punkte und die Weise der
Eintragungen beschrieben). Neben jedem Punkt sind die neu eingestellten Werte einzutragen.
Einen Inbetriebnahme-Setup durchführen:
nach Installation des G-PILOT 3380 Systems (siehe Abschn. 3).
nach Austausch eines Bauteiles, oder wenn System-Probleme vermutet werden.
Nach einem System-Setup, immer eine See-Erprobung durchführen (siehe Abschn. 5).
4-1 Inbetriebnahme-Setup
Warnung:Es ist keine Ruderlagen-Begrenzung vorhanden, solange der Rudergeber nicht kalibriert ist
(siehe Abschn. 4-2). Der Anwender muss sicherstellen, dass das Ruder nicht durch einen elektrischen
Steuerbefehl gegen die Hartlage gefahren werden kann (siehe BuchG-PILOT 3380 - Bedienung).
4-2 Ruderrückmelder kalibrieren
Diese Prozedur passt den Ruder-Rückmelder an die Ruderbewegungen an.
Hinweise
Zum sofortigen Abbruch der Kalibrierung ESC drücken.
Wird das Ruder nicht gemäß Aufforderung bewegt, oder falls der Rückgeber nicht richtig arbeitet, kann
das G-PILOT 3380 System nicht die Kalibrierung abschließen. Das G-PILOT 3380 System wird einen
Fehler anzeigen. ESC drücken, das Problem beseitigen und die Kalibrierung wiederholen.
Im normalen Betrieb wird das G-PILOT 3380 System das Ruder nicht näher als 3° zur Endlage bewegen.
Um den Rückmelder zu kalibrieren, folgende Menus anwählen: Setup > Calibrate > Rudder. Den
Bildschirm-Anweisungen zur Kalibrierung folgen (siehe Handbuch G-PILOT 3380 - Bedienung).
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Navman G-PILOT 3380 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Navman G-PILOT 3380 in the language / languages: German as an attachment in your email.

The manual is 0,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Navman G-PILOT 3380

Navman G-PILOT 3380 User Manual - English - 47 pages

Navman G-PILOT 3380 Installation Guide - English - 32 pages

Navman G-PILOT 3380 User Manual - German - 47 pages

Navman G-PILOT 3380 User Manual - Dutch - 47 pages

Navman G-PILOT 3380 Installation Guide - Dutch - 32 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info