Manual Navman FISH 4150 (page 23 of 25) (English)

470016

Zoom out

Zoom in

1/25

FISH 4100 Installation and Operation Manual NAVMAN

To stop problems from electrical noise, try:

- rerouting the power and transducer

cable(s) away from the boat’s other

electrical wiring.

- routing the unit's power cable directly to the

battery instead of through a fuse block or

ignition switch.

4. Bottom is not displayed:

a) The fishfinder may have Manual Range

selected and the depth may be outside the

range value selected. Either change the

fishfinder to Auto Range or select another

depth range - see section 3.8.

b) The depth may be outside the fishfinder’s range.

While in Auto Range, the display unit will flash

the last depth displayed, then display “--.-” to

indicate that there is no bottom detected. A

display of the bottom should reappear when it is

shallower than 180m (600ft).

5. The bottom is displayed too far up the screen:

The fishfinder may have Manual Range

selected and the selected Range value is too

high for the depth. Either change the fishfinder

to Auto Range or select another depth range -

see section 3-8.

6. Bottom echo disappears or erratic digital

reading while the boat is moving:

a) Ensure the back of the bottom surface of the

transducer is slightly lower than the front and

the front is as deep in the water as possible in

order to minimize the generation of bubbles

through cavitation. See the Transducer

Installation Guide for more information.

b) The transducer may be in turbulent water. Air

bubbles in the water disrupt the echoes

returned, interfering with the fishfinder’s ability

to find the bottom or other targets. This often

happens when the boat is reversed. The

transducer must be mounted in a smooth flow

of water in order for the fishfinder to work at all

boat speeds.

c) Electrical noise from the boat’s motor can

interfere with the fishfinder. Try some

suppression spark plugs.

7. If the fishfinder beeps when turned on but

nothing is displayed:

The fishfinder may be operating, but the

contrast settings may have been set too high

or low. Power off the fishfinder. Then hold

and press to reset the fishfinder to the

default contrast setting.

8. The wrong language is displayed:

See section 2.

9. The message "NO TRANSDUCER DETECTED.

ENTER SIMULATION MODE?" appears when you

turn the unit on:

a) Check to see that the blue transducer

connector is plugged into the top connector

(with the blue nut) on the rear of the display

unit.

b) Check the cable connectors are securely

plugged in and the blue collars are is locked in

place. The collars must be secure for water

tight connection.

c) Check that the plugs are clean and free of

water or anything that may short deteriorate the

quality of the connection. Inspect the

transducer cable from end to end for damage

such as cuts, breaks, stretched or squashed

sections.

sono in possesso di un navman fish 4150 e da un po di tempo non riesco piu a leggere perche non visualizza gli sritti quindi non riesco ad utilizarlo . Mi sapete dire cosa sara successo
Submitted on 31-12-2020 at 23:47
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Navman FISH 4150 in the language / languages: English as an attachment in your email.

The manual is 0,22 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Navman FISH 4150

Navman FISH 4150 Usermanual and installation guide - German - 27 pages

Navman FISH 4150 Usermanual and installation guide - Dutch - 25 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Navman FISH 4150 Manual

Product: