512556
30
Zoom out
Zoom in
Previous page
1/39
Next page
30
Diesel fuel flow sensor kit Installation and Operation Manual
NAVMAN
5
7
6
Install the required fittings to the straight
through pipe (for flare joints use a barrel union
fitting):
1 Apply thread sealer to the fitting’s ¼ NPT
threads.
Warning: Make sure pieces of the
threadseal tape or paste can not break
off and enter the fuel pipe (see section
7-2-5).
2 Screw each fitting in to the through pipe.
Use a spanner or wrench on the fitting and
another on the flats of the through pipe.
It does not matter which way round the through
pipe goes in the fuel line.
To attach a flare joint at the other end of the
sensor, repeat steps 3 and 4 above to bend
and cut the pipe, fit a flare nut and flare the
end of the pipe. Cut the pipe to length so the
flared end will meet the fittings on the sensor
port exactly. The exact amount you cut out will
depend on how much pipe length was used
up in the bends.
Otherwise, attach a different type of fitting
following the manufacturer’s instructions.
Hold the sensor in place and hand tighten the
fittings to check that the pipe lines up with the
sensor port and there is little strain on the joints.
Adjust the pipe bends so that the sensor will sit
flat against your chosen mounting surface.
Hold sensor in place
Put the flare nut on the pipe first!! Then flare
the end of the pipe using the flaring tool. Inspect
the inside face of the flared pipe - it must be
smooth and scratch-free. If it is not, cut the end
of the tube off and try again.
Put flare nut on first
4
Flare end of tube
Fit the straight through pipe. Tighten each fitting
with the correct tools (for a flare joint, use a
spanner or wrench on the flare nut and on the
barrel union). The fitting needs to be tight to
prevent leakage. Replace any pipe clamps that
you removed earlier.
Note: Leave the flare nut on the outlet side
of the install pipe loose now (see section 7-4,
step 5).
30


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Navman Diesel Fuel Flow Sensors at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Navman Diesel Fuel Flow Sensors in the language / languages: English as an attachment in your email.

The manual is 0,34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Navman Diesel Fuel Flow Sensors

Navman Diesel Fuel Flow Sensors User Manual - German - 34 pages

Navman Diesel Fuel Flow Sensors User Manual - Dutch - 32 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info