512555
17
Zoom out
Zoom in
Previous page
1/77
Next page
17
FUEL 3100 / DIESEL 3200 Installation and Operation Manual
NAVMAN
Warnings
1. The display unit is waterproof from the
front. Protect the rear from water, otherwise
water might enter the breathing hole and
damage the display unit. The warranty does
not cover damage caused by moisture or
water entering the back of the display unit.
2. Ensure that any holes cut for the
installation will not weaken the boats
structure. If in doubt, consult a qualified boat
builder.
50 mm (2") minimum
clearance for cables
20 mm (0.75")
maximum thickness
Fixing nutFixing hole
50 mm (2")
Side view of display unit mounting
4-2 The display unit
1 Choose a location for the display unit that:
is easily seen and protected from
damage
is at least 100 mm (4") from a compass
and at least 500 mm (19.5") from a radio
or radar antenna
is away from engines, fluorescent lights,
power inverters and radio or radar
transmitters
is accessible from the back; a minimum
clearance of 50 mm (2") is required at
the back (see mounting diagram)
protects the back of the unit from
moisture and water.
2 The unit must be mounted on a flat panel
less than 20 mm (0.75") thick. Stick the
mounting template in place. Drill a 50 mm
(2") fixing hole through the centre hole
in the template. Note that the template
allows space around the display unit for the
protective cover.
3 Remove the fixing nut from the back of
the display unit. Insert the stud at the back
of the display unit through the mounting
hole. Hand tighten the fixing nut.
4-3 The fuel flow sensor(s)
Install the fuel flow sensor(s) following the
instructions in the manual supplied with the
petrol fuel or diesel flow sensor(s). Note the
warning about fuel types in appendix B.
FUEL 3100: Plug the sensor cable into the
FUEL 3100 cable with a white connector and do
up the locking collar. For a twin engine or twin
tank boat, follow the instructions in the Fuel
Sensor Installation Manual.
DIESEL 3200: Connect the white sensor
cable to the DIESEL 3200. For a twin engine
installation install the white T connector and
then connect the sensor cables to this.
4-4 The speed sensor (optional)
If required, install the optional paddlewheel
speed sensor following the instructions in
the manual supplied with the sensor. Plug the
sensor cable into the FUEL 3100 cable with a
blue connector and do up the locking collar.
If a NavBus or NMEA speed source is used,
connect it to the power/data cable (see next
page).
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Navman Diesel 3200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Navman Diesel 3200 in the language / languages: English as an attachment in your email.

The manual is 2,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Navman Diesel 3200

Navman Diesel 3200 User Manual - German, Dutch, French - 77 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info