512555
14
Zoom out
Zoom in
Previous page
1/77
Next page
14
FUEL 3100 / DIESEL 3200 Installation and Operation Manual
NAVMAN
3-4 Fuel calibration (CAL.F)
To calibrate a fuel flow sensor, select CAL.F in
the FUEL menu. Calibrate the sensors if you are
doubtful of their performance.
FUEL 3100: It is essential to calibrate the fuel
flow sensors after installation and again after
the first 100 engine hours to allow moving parts
to wear in.
DIESEL 3200: The sensors are factory calibrated
and are highly accurate. They can be calibrated
but this should not be necessary.
Calibrating a fuel flow sensor requires accurate
measurement of the fuel consumption. This is
best done using a small portable tank. At least 4
gallons (15 litres) of fuel should be used to ensure
an accurate calibration. The more fuel used, the
more accurate the calibration.
Twin engine boats require both engines to
be calibrated. Do these together with two
portable tanks, or at different times using one
portable tank.
To calibrate an engine’s fuel flow sensor:
1 Connect the portable tank to the
engine through the fuel flow sensor.
2 Reset USED:
i Press one or more times
until USED is displayed.
ii If your boat has twin tanks,
press ENT one or more times
to display PORT or STBD.
iii Hold ENT and together until
the reading resets to zero.
3 Run the engine at normal cruising
speed until a known amount of
fuel, at least 15 litres (4 gallons),
has been used per engine.
4 Select the FUEL setup menu, then
select CAL.F; if your boat has twin
engines, select the PORT or STBD engine
to be calibrated (see section 3-1).
5 If the value of CAL.F does not match
the known amount of fuel used, press
ENT, then press or and change
CAL.F until it does match. Then press
ENT to save the correct value (otherwise
press ESC to ignore the calibration).
3-5 Fuel flow damping (dAmP.F)
Waves and rocking of the boat cause the fuel
flow to fluctuate slightly. To give a stable reading,
the instrument calculates flow by taking several
measurements over a period of time and
averaging them. This is called damping.
Set dAmP.F to between 1 to 99 seconds. Small
values will give more accurate readings but
will show fluctuations. Large values will give
more stable readings, but will ignore some
true fluctuations.
3-6 Speed input (InPUt)
Select the optional speed input:
No: No speed input is available.
GPS: Use GPS speed received via
NMEA. This is speed over ground.
SEn: The optional paddlewheel
sensor connected directly to the
unit, or through the Navbus system.
This is speed through water.
Note:
A speed input is required to display LOG,
TOTA L LOG, RANGE and SPEED (see
section 2-5).
Speed over ground and speed through water
can give different values for some displayed data
(see appendix C).
3-7 Speed damping (dAmP.S)
(Only available if an optional paddlewheel sensor
is connected to the unit and InPUt = SEn.)
Waves and rocking of the boat cause the speed
to fluctuate slightly. To give a stable reading,
the instrument calculates speed by taking
several measurements over a period of time and
averaging them. This is called damping.
Set dAmP.S to 1 (6 sec), 2 (12 sec), 3 (18 sec), 4
(24 sec) or 5 (30 sec). Small values will give more
accurate readings but will show uctuations.
Large values will give more stable readings, but
will ignore some true fluctuations.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Navman Diesel 3200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Navman Diesel 3200 in the language / languages: English as an attachment in your email.

The manual is 2,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Navman Diesel 3200

Navman Diesel 3200 User Manual - German, Dutch, French - 77 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info