707134
56
Zoom out
Zoom in
Previous page
1/85
Next page
Just under the status/mode indicators are three small, but important buttons.
S (Snap): Pressing the Snap on/off button toggles TRAKTOR's global Snap feature on or
off. When global Snap is on, the button also lights up blue and is off when Snap is off.
Settings button: The Settings button toggles the Settings mode on and off. This only
works when TRAKTOR is connected (i.e., not when you use the Z2 in Direct mode; see
also 5.4.8, TRAKTOR Buttons). The Settings button blinks on and off when the Settings
mode is active. There are three different sets of parameters which you can control in Set-
tings Mode: Timecode Parameters, LED Meter Parameters, and Layout Parameters. You can
switch between the three different kinds of parameters by turning the left LOOP (SIZE)
encoder. See the sections below for a description of the parameters.
Q (Quantize): The Quantize button activates/deactivates the global Quantize in TRAKTOR.
When the button is on (blue), global Quantize is engaged and when the button not lit,
global Quantize is also off.
Timecode Parameters
See the Settings button's +description above to see how to enter this Settings mode. The
Timecode Parameter is shown by "tC" on the left LED display. The right display gives you a
number of options:
Calibrate Deck A: This is represented by "C_A" on the right LED display. You can trigger
the calibaration for Deck A by pressing the right LOOP (SIZE) encoder.
Calibrate Deck B: The right display shows "C_b". Press the encoder to trigger calibration for
Deck B.
Deck Swap: The right display shows the current configuration which is "A_b" by default. To
swap Decks A and B, just press the right LOOP (SIZE) encoder and it will display "b_A".
Press again to toggle back to the previous state.
Reset: The right display shows "rES". Press the right LOOP (SIZE) encoder to reset all in-
put and output routing configurations to their default values.
TRAKTOR KONTROL Z2 Hardware Reference
Top Panel
TRAKTOR KONTROL Z2 - Manual - 56
56


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Native Traktor Kontrol Z2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Native Traktor Kontrol Z2 in the language / languages: English as an attachment in your email.

The manual is 1,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Native Traktor Kontrol Z2

Native Traktor Kontrol Z2 User Manual - German - 90 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info