637931

Napoleon BISZ 300 Manual

29
Zoom out
Zoom in
Previous page
1/40
Next page
29
www.napoleongrills.com
ATTENTION! Lors du déballage et de l’assemblage, nous vous conseillons de porter des gants de travail et
des lunees de sécurité pour votre protecon. Malgré tous nos eorts pour assurer que l’assemblage soit aussi
sécuritaire et sans problème que possible, il se peut que les bords et les coins des pièces usinées en acier soient
coupants et qu’ils causent des coupures si les pièces ne sont pas manipulées correctement.
CAUTION! During unpacking and assembly we recommended you wear work gloves and safety glasses
for your protecon. Although we make every eort to make the assembly process as problem free and safe as
possible, it is characterisc of fabricated steel parts that the edges and corners might be sharp and could cause cuts
if handled incorrectly.
Geng Started
1. Remove all cart panels, hardware, and grill head from carton. Raise lid and remove any components packed
inside. Use the parts list to ensure all necessary parts are included.
2. Do not destroy packaging unl the grill has been fully assembled and operates to your sasfacon.
3. Assemble the grill where it is to be used, lay down cardboard or a towel to protect parts from being lost or
damaged while assembling.
4. Most stainless steel parts are supplied with a protecve plasc coang that must be removed prior to using
the grill. The protecve coang has been removed from some of the parts during the manufacturing process
and may have le behind a residue that can be perceived as scratches or blemishes. To remove the residue,
vigorously wipe the stainless steel in the same direcon as the grain.
5. Follow all instrucons in the order that they are laid out in this manual.
6. Two people are required to li the grill head onto the assembled cart.
If you have any quesons about assembly or grill operaon, or if there are damaged or missing parts please call our
Customer Soluons Department at 1-866-820-8686 between 9 AM and 5 PM (Eastern Standard Time).
Pour Commencer
1. Rerez tous les panneaux, le matériel et le gril du carton d’emballage. Soulevez le couvercle et enlevez les com-
posants qui se trouvent à l’intérieur. Servez-vous de la liste de pièces pour vous assurer que toutes les pièces
nécessaires sont incluses.
2. Ne détruisez pas l’emballage jusqu’à ce que le gril ait été complètement assemblé et qu’il fonconne à votre sas-
facon.
3. Assemblez le gril là où il sera ulisé et posez un carton ou une serviee an d’éviter de perdre ou d’endommager
les pièces lors de l’assemblage.
4. La plupart des pièces en acier inoxydable comportent un revêtement de protecon en plasque qui doit être
reré avant d’uliser le gril. Le revêtement de protecon a déjà été reré de certaines pièces lors du processus
de fabricaon, ce qui a pu laisser un résidu pouvant être perçu comme des égragnures ou des marques. Pour
enlever ce résidu, froez l’acier inoxydable vigoureusement dans le sens du grain.
5. Suivez toutes les instrucons dans l’ordre donné dans ce manuel.
6. Deux personnes sont requises pour soulever la cuve de gril et la placer sur le chariot assemblé.
Si vous avez des quesons à propos de l’assemblage ou du fonconnement du gril, ou si des pièces sont man-
quantes ou endommagées, veuillez appeler notre département du Service aux Consommateurs au 1-866-820-8686
entre 9 h et 17 h (heure normale de l’Est).
OUTILS REQUIS POUR L’ASSEMBLAGE (ouls non inclus)
TOOLS REQUIRED FOR ASSEMBLY (tools not included)
WARNING! Construcon materials and masonry dust may cause surface damage to units and accessories.
The best opon is to install components aer all construcon has been completed and the jobsite has been
thoroughly cleaned. If the components must be installed prior to the construcon being completed, then exposed
surfaces need to be covered to prevent corrosion. All surfaces must be cleaned when construcon is completed.
Do not use muriac acid to clean masonry materials from any surfaces. The lime contained in some construcon
materials is extremely corrosive. During its curing period, (1 - 2 months) it is recommended that a stainless steel
polish or wax (car wax is acceptable) be applied to prevent direct contact of the lime materials.
3/8” (10 mm)
AVERTISSEMENT! La poussière des matériaux de construcon et de maçonnerie peut endommager la
surface des unités et des accessoires. Ainsi, il est préférable de procéder à l’installaon des composants une fois
la construcon achevée et le chaner soigneusement neoyé. Si les composants doivent être installés avant la n
des travaux, couvrez les surfaces exposées an de prévenir la corrosion. Toutes les surfaces doivent être neoyées
une fois la construcon terminée. N’ulisez pas d’acide chlorhydrique pour neoyer les matériaux de maçonnerie
sur toute surface. La chaux contenue dans certains matériaux de construcon est extrêmement corrosive. Pendant
sa période de durcissement (1 à 2 mois), il est recommandé d’appliquer un vernis ou une cire (une cire automobile
convient) pour l’acier inoxydable an d’éviter le contact direct avec les matériaux de chaux.
… 29 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Napoleon BISZ 300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Napoleon BISZ 300 in the language / languages: English, French as an attachment in your email.

The manual is 4,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info