637914

Napoleon BIPRO 500 Manual

20
Zoom out
Zoom in
Previous page
1/68
Next page
20
www.napoleongrills.com
EN
BI ACCESSORY DRAWER INSTRUCTIONS
BI ACCESSORY DOOR INSTRUCTIONS
1. Unpack the drawer frame assembly.
2. Remove the drawers from the enclosure by fully extending them and then liing up to remove them from the
slides.
3. Shim the opening to ensure that the enclosure ts snuggly into the opening. Ensure that the side shims are
located at the same height as the enclosure mounng holes. The boom of the opening may need to be shimmed as
well to ensure that the front of the enclosure is plumb.
4. Once the enclosure is level and square, fasten into place. (Fasteners not included).
5. Re-install the drawers by pping the back of the drawer down into the slide. Once the wheels are inserted into the
slide, lower the front of the drawer unl it is level, then push in.
Note: if the enclosure is installed with shims that are too thick, the wheel will not engage into the slide. The shim
thickness will need to be reduced.
6. Remove the protecve coang from all remaining surfaces.
1. Unpack the door and frame.
a. For the PF style stainless steel door, the door needs to be removed by loosening the center phillips screw on the
hinge furthest away from the door. This will allow the hinge to separate.
b. For double door kits N370-0502-1/N370-0503-1, refer to the instrucons included with the door kit.
2. Center the frame in the opening. Mark the locaon of the pivot holes, top and boom. Once all pivot holes are
marked, remove the frame and using a 3/8” (10mm) drill bit, drill out the clearance holes for the pivot rod. These
clearance holes should be at least 1/2” (13mm) deep. Aer the holes are complete, you may once again center the
frame in the opening. Starng with the hinged side, shim between the frame and side wall of the opening. Ensure
the shims are close to the hinge on the PF style doors. When the frame side wall is plumb, fasten it to the cabinet
with screws (not provided). Aach the other side of the frame in the same fashion, ensuring the frame is square.
3. Other than on the curved stainless steel double door kit, fasteners are not required on the top and boom of the
frame. The curved stainless steel double door frame must be fastened in the center both at the top and boom.
4. Once the frame has been secured and checked for squareness, the door can be re-installed.
5. Remove the protecve coang from all remaining surfaces.
BIPRO500 BUILT-IN INSTRUCTIONS
… 20 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Napoleon BIPRO 500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Napoleon BIPRO 500 in the language / languages: English, German as an attachment in your email.

The manual is 7,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info