637911
18
Zoom out
Zoom in
Previous page
1/56
Next page
www.napoleongrills.com
18
EN
BI ACCESSORY DRAWER INSTRUCTIONS
BI ACCESSORY DOOR INSTRUCTIONS
1. Unpack the drawer frame assembly.
2. Remove the drawers from the enclosure by fully extending them and then liing up to remove them from
the slides.
3. Shim the opening to ensure that the enclosure ts snuggly into the opening. Ensure that the side shims
are located at the same height as the enclosure mounng holes. The boom of the opening may need to be
shimmed as well to ensure that the front of the enclosure is plumb.
4. Once the enclosure is level and square, fasten into place. (Fasteners not included).
5. Re-install the drawers by pping the back of the drawer down into the slide. Once the wheels are inserted
into the slide, lower the front of the drawer unl it is level, then push in. Note: if the enclosure is installed
with shims that are too thick, the wheel will not engage into the slide. The shim thickness will need to be
reduced.
6. Remove the protecve coang from all remaining surfaces.
1. Unpack the door and frame.
a. For the curved stainless steel doors, remove the door(s) from the frame by liing the door while holding on
to the pivot rod. This will allow the pivot rod to come out of the hole on the boom of the frame. Once the
pivot is removed from the boom hole, the enre door can be dropped and removed from the frame.
b. For the PF style stainless steel door, the door needs to be removed by loosening the center philips screw on
the hinge furthest away from the door. This will allow the hinge to separate.
c. For double door kits N370-0502-1/N370-0503-1, refer to the instucons included with the door kit.
2. Center the frame in the opening. Mark the locaon of the pivot holes, top and boom. Remember on the
PT600 double doors, there will be a pivot rod on both ends. The PF style doors do not have pivot rods. Once
all pivot holes are marked, remove the frame and using a 3/8” drill bit, drill out the clearance holes for the
pivot rod. These clearance holes should be at least 1/2” deep. Aer the holes are complete, you may once
again center the frame in the opening. Starng with the hinged side, shim between the frame and side wall
of the opening. Ensure the shims are close to the hinge on the PF style doors. When the frame side wall is
plumb, fasten it to the cabinet with screws (not provided). Aach the other side of the frame in the same
fashion, ensuring the frame is square.
3. Other than on the curved stainless steel double door kit, fasteners are not required on the top and boom
of the frame. The curved stainless steel double door frame must be fastened in the center both at the top and
boom.
4. Once the frame has been secured and checked for squareness, the door can be re-installed.
5. Remove the protecve coang from all remaining surfaces.
BILEX485 BUILT-IN INSTRUCTIONS
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Napoleon BILEX 485 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Napoleon BILEX 485 in the language / languages: English, French as an attachment in your email.

The manual is 9,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Napoleon BILEX 485

Napoleon BILEX 485 User Manual - English, German - 52 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info