707503
11
Zoom out
Zoom in
Previous page
1/22
Next page
E9
Note: The AV Bypass feature must be used with care. It
bypasses the NAIT XS 2 volume control leaving any signal
connected to the av input to be passed to the speakers at
full volume.
Note: Inserting a headphone plug while AV Bypass mode
is selected temporarily returns the NAIT XS 2 to normal
operation. Removing the headphone plug will return the
NAIT XS 2 to AV Bypass mode.
Note: The mute function is disabled when AV Bypass
mode is engaged.
8.7 Other Signal Inputs and Outputs
The NAIT XS 2 incorporates RCA phono sub out, DIN pre-
amp out, and DIN power-amp in sockets on its rear panel. In
normal use the pre-amp out and power-amp in sockets are
connected by a link plug. The link plug should be removed
only in the following circumstances:
A power supply upgrade is to be used.
An alternative preamplier is to be used with the
NAIT XS 2 power amplier. See Section 8.8
An alternative power amplier is to be used with the
NAIT XS 2 preamplier.
Note: The power amp in socket carries a 24V DC power
supply output intended for Naim preampliers that
require an external power supply.
The RCA phono sub out sockets provide a stereo output
intended for connection to an active subwoofer. The output
signal is a duplicate of the preamplier output. No low-pass
ltering is applied.
8.8 Power Amp Mode Operation
If a NAIT XS 2 is to be used as a stereo power amp only it
must be congured to operate in power amp mode:
With the NAIT XS 2 switched o, remove its rear panel
link plug and connect the interconnect cable from the
preamp or preamp power supply to the power amp in
socket
Switch on the NAIT XS 2. The mute button will ash to
indicate that the link plug has been removed. Press and
hold the mute button until it extinguishes. The NAIT
XS 2 is now in power amp mode. Its volume control
indicator and button illumination will extinguish.
To return the NAIT XS 2 to normal operation, switch it
o, replace the link plug and switch it on again.
8.9 Power Supply Upgrades
The NAIT XS 2 preamplier can be upgraded through the
connection of an external Flatcap, Hi-Cap or Supercap
power supply. The NAIT XS 2 and external power supply
must be switched o when connections are made. Switch
on the external power supply rst followed by the NAIT XS 2
when all connections are complete.
8.10 General Connections Notes
The NAIT XS 2 negative input and output connections for
each channel are common. The mains earth (ground) should
always be connected regardless of what other equipment is
used in conjunction with the amplier. The mains earth only
grounds the case and the electrostatic screen within the
transformer, and is not connected to the signal negative. In
order to avoid hum loops, the signal negative of the whole
system should be connected to the mains earth (ground) in
one place.
A signal ground connection is tted to the NAIT XS 2 rear
panel. This is intended to be used to connect a turntable
pick-up arm signal earth only.
8.11 External Control and Interface
The NAIT XS 2 is tted on its rear panel with a 3.5mm jack
Remote In socket and a mini-USB interface socket.
The Remote In socket can be used for RC5 remote control
of the NAIT XS 2 via a wired connection or a remote IR
repeater.
The mini-USB socket enables rmware upgrades and
diagnostic tests to be carried out. Contact your Naim
retailer for more information if required.
Note: The mini-USB interface is not intended for the
connection of USB memory devices.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Naim SUPERNAIT 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Naim SUPERNAIT 2 in the language / languages: English as an attachment in your email.

The manual is 2,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Naim SUPERNAIT 2

Naim SUPERNAIT 2 User Manual - German - 22 pages

Naim SUPERNAIT 2 User Manual - Dutch - 22 pages

Naim SUPERNAIT 2 User Manual - French - 22 pages

Naim SUPERNAIT 2 User Manual - Italian - 22 pages

Naim SUPERNAIT 2 User Manual - Polish - 22 pages

Naim SUPERNAIT 2 User Manual - Spanish - 22 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info