707511
8
Zoom out
Zoom in
Previous page
1/20
Next page
2.2 NAC S1 CONNECTION PANEL
E2378
2.3 NAC S1 AUDIO OUTPUTS AND CONNECTIONS
The NAC S1 preamplifier is fitted with two pairs of analogue stereo audio outputs: one pair of 4-pin
DIN sockets and one pair of balanced XLR sockets. A slide switch on the connection panel enables
the selection of the XLR, DIN or both output sockets.
If the NAC S1 is to be used with a Nim 500 Series or Classic Series power amplifier (most likely
a NAP 500 or NAP 300), the left and right DIN output sockets should be connected to the power
amplifier channel 1 and 2 inputs respectively using Nim 4-pin DIN to XLR interconnect cables.
Your Nim retailer will be able to supply appropriate cables. The output socket switch should be
in the DIN position.
If the NAC S1 is to be used with a pair of NAP S1 power amplifiers, the left and right balanced XLR
output sockets should be connected to the left and right power amplifier inputs using the XLR to
XLR interconnect cables supplied with the power amplifiers. If longer cables are required your
Nim retailer will be able to provide cables of the desired length. The output socket switch should
be in the BAL position.
If the NAC S1 is to be used with both Classic Series power amplification and a pair of NAP S1 power
amplifiers simultaneously, the left and right balanced XLR output sockets should be connected to
the left and right NAP S1 inputs using XLR to XLR interconnect cables. The the left and right DIN
output sockets should be connected to the Classic Series power amplifier channels 1 and 2 inputs
respectively using Nim 4-pin DIN to XLR interconnect cables. The NAC S1 output socket switch
should be in the DIN+BAL position.
DIN inputs: 1, 2 & 3
Phono inputs: 4, 5 & 6
Upper sockets: Left
Lower sockets: Right
Outputs:
XLR: balanced
DIN: unbalanced
Control:
RJ45: CAN bus x 3
RS232 × 1
Jack: Trigger in x 1
Trigger out x 2
IR in x 1
USB: Firmware update
Balanced XLR inputs:
7 & 8
Mains power and fuse
Input indicator
Output socket
selection switch
Auxiliary signal ground
connector
Power switch
2.0 NAC S1 PREAMPLIFIER
Each of the five NAC S1 inputs can be independently adjusted for input gain. Input gain
adjustment enables signal levels from different source components to be compensated so that
switching inputs is less likely to require preamplifier volume adjustment. Adjustment of input
gain is described in Section 4.2.
A signal ground terminal on the NAC S1 connection panel enables the termination of specialist
interconnect cables with auxiliary ground conductors. Contact your Nim retailer for advice on
using such interconnect cables.
Always use interconnect cables intended for high-end audio applications to connect source
equipment to the NAC S1 inputs. Nim interconnect cables will always provide the best results.
Input gain and mapping set
up
14 15
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Naim NAP S1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Naim NAP S1 in the language / languages: English as an attachment in your email.

The manual is 3,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Naim NAP S1

Naim NAP S1 User Manual - German - 38 pages

Naim NAP S1 User Manual - French - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info