707510
5
Zoom out
Zoom in
Previous page
1/16
Next page
E3
NAP 500
4. NAP 500 Installation and Operation
The NAP 500 and NAP 500PS should be installed on a dedicated equipment stand intended for the purpose and should be
in their nal location before connecting cables or switching on. Switch on the source and preamplier components, with the
volume turned down, before switching on the NAP 500. The NAP 500 power button is located on the front panel of the NAP
500PS Power Supply.
Care should be taken when siting the NAP 500 to ensure that the top and bottom ventilation grids are not blocked.
The NAP 500 and NAP 500PS are very heavy and care should be taken when lifting or moving them. Make sure that the
surface they are to be placed on can support the full weight.
4.1 General Connections Notes
The mains earth (ground) should always be connected
regardless of what other equipment is used in conjunction
with Naim power ampliers. This only grounds the case
and the electrostatic screen within the transformer, and is
not connected to the signal negative. In order to avoid hum
loops, the signal negative of the whole system should be
connected to the mains earth (ground) in one place.
Note: Each channel of the NAP 500 is a “bridged”
amplier, so none of the speaker outlet sockets (+ or -)
are at earth potential. Avoid connecting mains powered
equipment such as electrostatic speakers, sub-woofers
and headphone energisers that do not have a oating
earth. No plug which is connected directly or indirectly to
earth potential should be attached to any speaker outlet
(+ or -).
4.2 Protection Notes
In the NAP 500 the fan speed is increased in response to
an increase in amplier dissipation. If the amplier reaches
70°C due to prolonged running at high level or to airow
being blocked, the output will be interrupted and the fan
will run at full speed until it has cooled down. This may take
a few minutes.
It is not necessary to switch the amplier o, but it may be
advisable to mute the preamplier or turn the volume down
to avoid surprises when it comes back on.
OPERATION OF THE AMPLIFIER’S THERMAL PROTECTION
SUGGESTS PROLONGED USE AT TOO HIGH A VOLUME
LEVEL. YOUR LOUDSPEAKERS MAY BE AT RISK IF THIS IS
THE CASE. THE VOLUME SHOULD BE REDUCED.
4.3 Loudspeaker Cable and Connectors
Only Naim Audio speaker cable should be used to connect
a loudspeaker to the output of the NAP 500. Custom Naim
Audio loudspeaker connectors are supplied to make the
connection and in order to comply with current European
safety regulations these should always be used.
DAMAGE TO THE AMPLIFIER MAY RESULT IF “HIGH
DEFINITION” CABLE OR ANY OTHER SPECIAL CABLE IS
USED TO CONNECT THE LOUDSPEAKERS.
Ensure when connecting speakers that they are “in phase.
That is, the positive and negative connection orientation at
both the speaker and amplier ends of the cable is the same
for both channels.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Naim NAP 500 DR at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Naim NAP 500 DR in the language / languages: English as an attachment in your email.

The manual is 1,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Naim NAP 500 DR

Naim NAP 500 DR User Manual - English - 44 pages

Naim NAP 500 DR User Manual - German - 44 pages

Naim NAP 500 DR User Manual - German - 16 pages

Naim NAP 500 DR User Manual - Dutch - 16 pages

Naim NAP 500 DR User Manual - French - 44 pages

Naim NAP 500 DR User Manual - French - 16 pages

Naim NAP 500 DR User Manual - Italian - 46 pages

Naim NAP 500 DR User Manual - Italian - 16 pages

Naim NAP 500 DR User Manual - Polish - 16 pages

Naim NAP 500 DR User Manual - Spanish - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info