707509
24
Zoom out
Zoom in
Previous page
1/44
Next page
E22
NAIT XS Integrated Amplifier
22 NAIT XS Introduction, Installation and Connections
The NAIT XS should be installed on a dedicated equipment stand intended for the
purpose. Do not stand it directly on top of another item of equipment. Care should
be taken to ensure that it is level. The amplifier should be installed in its final location
before connecting cables or switching on. Ensure that the volume is turned down before
switching on.
A variety of power supply upgrade, alternative preamplifier and alternative or additional
power amplifier options are possible for the NAIT XS. Diagrams illustrating the connection
of some of these are shown in Section 23. Contact your local retailer or distributor for
advice on further alternative connection schemes.
The NAIT XS incorporates an AV Bypass switch on its rear panel. The switch should only
be set to “On” if the amplifier is to be used in conjunction with an AV processor in a
home theatre system. In all other installations the AV Bypass switch should be set to “Off”.
Speaker and/or amplifier damage may occur if a signal is inadvertently connected to the
NAIT XS av input while the AV Bypass switch is “On”.
Operational features common to all preamplifiers and integrated amplifiers are described
in Section 28.
22.1 Mains Power Connection
Connect the NAIT XS to a mains power socket using either
the mains cable supplied or a Naim Power-Line.
22.2 Signal Inputs
The NAIT XS front panel input buttons select the source
input signal to be routed to the integral power amplifier
and the loudspeakers. The six buttons are labelled cd,
tuner, hdd, av, aux 1 and aux 2.
The cd, tuner, hdd and av input buttons select parallel DIN
and RCA phono input sockets on the rear panel.
Note: The hdd and av sockets carry both inputs and
outputs. See Section 22.4 for more information.
The aux 1 input button corresponds to a pair of RCA
phono sockets on the rear panel and a parallel 3.5mm
stereo jack socket on the front panel. Insertion of a plug
into the front panel aux 1 socket will automatically switch
the amplifier to that input. Removal of the plug will return
the amplifier to the previously selected input. If a different
input is selected while a plug is inserted removal of the
plug will not cause the input to change.
The aux 2 input button corresponds to a DIN input socket
on the rear panel. The aux 2 DIN socket also carries a
power supply output suitable to power a Naim
Stageline
or
SuperLine phono preamplifier.
Note: For optimum sound quality DIN sockets should be
used in preference to RCA phono sockets.
Note: Where an input has DIN or Phono socket options only
one should be connected at any one time.
Always use high quality interconnect cables to connect
sources to inputs. The Naim Hi-Line will produce the best
results.
22.3 Speaker Outputs
A set of stereo speaker connection sockets is provided on
the rear panel. Custom Naim loudspeaker connectors are
supplied to make the connection and in order to comply
with current European safety regulations these should
always be used. Naim speaker cable will provide the best
results, however, a wide range of speaker cable types can
be used without risk of damage to the amplifier.
Ensure when connecting speakers that they are “in
phase”. That is, the positive and negative connection
orientation at both the speaker and amplifier ends of the
cable is the same for both channels.
22.4 AV and hdd Inputs and Outputs
The NAIT XS av and hdd inputs have associated outputs
that enable the selected input signal to be routed
externally; to an audio recording component for example.
Note: The av or hdd outputs will be muted if their
corresponding inputs are selected.
22.5 AV Bypass
The NAIT XS can be integrated within a multi-channel
home theatre system, driving the front left and right
channel speakers, by engaging its AV Bypass mode. AV
Bypass mode enables a home theatre processor to take
over volume control of signals connected to the NAIT XS av
input. It is engaged using the switch on the rear panel. The
NAIT XS volume control indicator will extinguish when AV
Bypass mode is engaged and the av input is selected. The
remote handset volume control will also be disabled.
Operational features
common to all
preamplifiers and
integrated amplifiers
are described in
Section 28
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Naim NAP 300 DR at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Naim NAP 300 DR in the language / languages: English as an attachment in your email.

The manual is 1,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Naim NAP 300 DR

Naim NAP 300 DR User Manual - English - 16 pages

Naim NAP 300 DR User Manual - German - 44 pages

Naim NAP 300 DR User Manual - French - 44 pages

Naim NAP 300 DR User Manual - Italian - 46 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info