707508
43
Zoom out
Zoom in
Previous page
1/44
Next page
E41
49.1 General Connections Notes
The mains earth grounds only the case and the
electrostatic screen within the transformer and is not
connected to the signal negative. The mains earth must
always be connected to “ground” regardless of any other
equipment used. In order to avoid hum-loops the signal
negative of the whole system should be connected to the
mains earth in one place.
49.2 Protection Notes
Once installed the NAP V175 is intended to remain
permanently powered up via its rear panel switch. If the
internal heatsink reaches 70°C due to prolonged running
at very high dissipation the mains supply will be interrupted
and the illuminated logo will go off until the amplifier has
cooled down. This may take up to thirty minutes.
49 Installation and Operation
The NAPV 175 is a three channel power amplifier intended for use in audio-visual systems.
The three channels provide power to drive a centre channel speaker and a pair of
either main front or surround channel speakers. Audio line level input is via two 4-pin DIN
sockets - one for the centre channel and one for the main or surround pair.
The NAPV 175 should be installed on an equipment rack intended for the purpose and
in its final location before connecting cables or switching on. Switch on the source and
preamplifier components, with the volume turned down, before switching on the NAPV
175. The power switch is located on the rear panel.
The NAPV 175 is heavy and care should be taken when lifting or moving it. Make sure that
the surface it is to be placed on can support the full weight.
OPERATION OF THE AMPLIFIER’S THERMAL PROTECTION
SUGGESTS PROLONGED USE AT TOO HIGH A VOLUME LEVEL.
YOUR LOUDSPEAKERS MAY BE AT RISK IF THIS IS THE CASE.
THE VOLUME SHOULD BE REDUCED.
49.3 Loudspeaker Cable and Connectors
Only Naim Audio speaker cable should be used to
connect a loudspeaker to the output of the NAPV 175.
Custom Naim Audio loudspeaker connectors are supplied
to make the connection and in order to comply with
current European safety regulations these should always
be used.
DAMAGE TO THE AMPLIFIER MAY RESULT IF “HIGH
DEFINITION” CABLE OR ANY OTHER SPECIAL CABLE IS USED
TO CONNECT THE LOUDSPEAKERS.
Ensure when connecting speakers that they are “in
phase”. That is, the positive and negative connection
orientation at both the speaker and amplifier ends of the
cable is the same for all channels.
51 NAPV 175 Specification
Power Output: 50 Watts per channel, 8Ω
Channels: Three
Quiescent Consumption:
10VA
Voltage Gain:
+29dB
Input Impedance:
18kΩ
Frequency Response: -3dB @ 3Hz and 50kHz
Dimensions (H x W x D): 70 x 432 x 301mm
Weight 7.9kg
Mains Supply: 100-120V or 220-240V, 50/60Hz
mains
input and
fuse
signal input
ch1(L) &
ch2(R)
power
switch
signal
input
centre
nc
signal
nc
Input - Centre
-ve
ch2
ch1
nc
Input -
Ch1 & Ch2
-ve
NAPV 175 Power Amplifier
left
speaker
right
speaker
centre
speaker
50 NAPV 175 Connections
50.1 NAPV 175 Rear
43


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Naim NAP 250 DR at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Naim NAP 250 DR in the language / languages: English as an attachment in your email.

The manual is 1,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Naim NAP 250 DR

Naim NAP 250 DR User Manual - English - 16 pages

Naim NAP 250 DR User Manual - German - 44 pages

Naim NAP 250 DR User Manual - French - 44 pages

Naim NAP 250 DR User Manual - Italian - 46 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info