707507
11
Zoom out
Zoom in
Previous page
1/16
Next page
E9
NAP 200
12. NAP 200 Installation and Operation
The NAP 200 should be installed on a dedicated equipment stand intended for the purpose and should be in its nal location
before connecting cables or switching on. Switch on the source and preamplier components, with the volume turned down,
before switching on the NAP 200. The NAP 200 power button is located on the front panel.
The NAP 200 can provide power for an appropriate Naim Audio preamplier. The power supply output is carried on the DIN
input socket.
The NAP 200 is heavy and care should be taken when lifting or moving it. Make sure that the surface it is to be placed on can
support its full weight.
12.1 General Connections Notes
The negative input and output connections are all common.
The mains earth should always be connected regardless of
what other equipment is used. This only grounds the case
and the electrostatic screen within the transformer, and is
not connected to the signal negative. In order to avoid hum
loops, the signal negative of the whole system should be
connected to the mains earth (ground) in one place.
12.2 Protection Notes
If the ampliers external case reaches 70°C due to
prolonged running at high power, the mains supply will be
interrupted and the illuminated logo will switch o until
the amplier has cooled down. This may take up to thirty
minutes.
OPERATION OF THE AMPLIFIER’S THERMAL PROTECTION
SUGGESTS PROLONGED USE AT TOO HIGH A VOLUME
LEVEL. YOUR LOUDSPEAKERS MAY BE AT RISK IF THIS IS
THE CASE. THE VOLUME SHOULD BE REDUCED.
12.3 Loudspeaker Cable and Connectors
Only Naim Audio speaker cable should be used to connect
a loudspeaker to the output of the NAP 200. Custom Naim
Audio loudspeaker connectors are supplied to make the
connection and in order to comply with current European
safety regulations these should always be used.
DAMAGE TO THE AMPLIFIER MAY RESULT IF “HIGH
DEFINITION” CABLE OR ANY OTHER SPECIAL CABLE IS
USED TO CONNECT THE LOUDSPEAKERS.
Ensure when connecting speakers that they are “in phase.
That is, the positive and negative connection orientation at
both the speaker and amplier ends of the cable is the same
for both channels.
FUSE RATING: ANTISURGE
100V TO 120V: T6.3AL.
200V TO 240V: T3.15AL/250V.
AC ONLY
FREQUENCY: 50/60Hz
INPUT POWER: 140VA
ch1 left+
+
WARNING:
DO NOT REPLACE SUPPLIED LOUDSPEAKER
PLUGS WITH INDIVIDUAL 4mm PLUGS
LoudspeakerPower Input
-ve
ch2
+24V 0.3A
ch1
ch2 right
WARNING:
DO NOT REPLACE SUPPLIED LOUDSPEAKER
PLUGS WITH INDIVIDUAL 4mm PLUGS
-
-
Loudspeaker
WARNING:
DISCONNECT SUPPLY CORD
BEFORE OPENING
ATTENTION:
DEBRANCHER AVANT D’OUVRIR
WARNING:
THIS APPARATUS MUST
BE EARTHED
DESIGNED AND MADE IN ENGLAND BY NAIM AUDIO LTD.
SOUTHAMPTON ROAD, SALISBURY
NAP 200
PLEASE READ THE MANUAL BEFORE USE
CONFORMS
TO EN 60065
S/No.
E2378
DR
13. NAP 200 Connections
13.1 NAP 200 Rear
+V
ch2
-ve
ch1
24V
0.3A
Input/Preamp
Power Output
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Naim NAP 200 DR at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Naim NAP 200 DR in the language / languages: English as an attachment in your email.

The manual is 1,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Naim NAP 200 DR

Naim NAP 200 DR User Manual - English - 44 pages

Naim NAP 200 DR User Manual - German - 44 pages

Naim NAP 200 DR User Manual - French - 44 pages

Naim NAP 200 DR User Manual - Italian - 46 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info