707507
40
Zoom out
Zoom in
Previous page
1/44
Next page
E38
40.1 General Connections Notes
The negative input and output connections are all
common. The mains earth should always be connected
regardless of what other equipment is used. This only
grounds the case and the electrostatic screen within the
transformer, and is not connected to the signal negative.
In order to avoid hum loops, the signal negative of the
whole system should be connected to the mains earth
(ground) in one place.
40.2 Protection Notes
If the amplifier’s external case reaches 70°C due to
prolonged running at high power, the mains supply will be
interrupted and the illuminated logo will switch off until
the amplifier has cooled down. This may take up to thirty
minutes.
40 Installation and Operation
The NAPV 145 is a mono power amplifier intended for use in audio-visual systems. The
NAPV 145 should be installed on a dedicated equipment stand intended for the purpose
and should be in its final location before connecting cables or switching on. Switch on the
source and preamplifier components, with the volume turned down, before switching on
the NAPV 145. The NAPV 145 power button is located on the front panel.
The NAPV 145 is heavy and care should be taken when lifting or moving it. Make sure that
the surface it is to be placed on can support the full weight.
OPERATION OF THE AMPLIFIER’S THERMAL PROTECTION
SUGGESTS PROLONGED USE AT TOO HIGH A VOLUME LEVEL.
YOUR LOUDSPEAKERS MAY BE AT RISK IF THIS IS THE CASE.
THE VOLUME SHOULD BE REDUCED.
40.3 Loudspeaker Cable and Connectors
Only Naim Audio speaker cable should be used to
connect a loudspeaker to the output of the NAPV 145.
Custom Naim Audio loudspeaker connectors are supplied
to make the connection and in order to comply with
current European safety regulations these should always
be used.
DAMAGE TO THE AMPLIFIER MAY RESULT IF “HIGH
DEFINITION” CABLE OR ANY OTHER SPECIAL CABLE IS USED
TO CONNECT THE LOUDSPEAKERS.
Ensure when connecting speakers that they are “in
phase”. That is, the positive and negative connection
orientation at both the speaker and amplifier ends of the
cable is the same for both channels.
mains input
and fuse
signal input
NAPV 145 Power Amplifier
42 NAPV 145 Specification
Power Output: 80 Watts, 8Ω
400 VA Transient
Quiescent Consumption:
15VA
Voltage Gain:
+29dB
Input Impedance:
18kΩ
Frequency Response: -3dB @ 2Hz and 65kHz
Dimensions (H x W x D): 87 x 432 x 314mm
Weight 15.8kg
Mains Supply: 100-120V or 220-240V, 50/60Hz
speaker
41 NAPV 145 Connections
41.1 NAPV 145 Rear
nc
-ve
i/p
Input
40


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Naim NAP 200 DR at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Naim NAP 200 DR in the language / languages: English as an attachment in your email.

The manual is 1,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Naim NAP 200 DR

Naim NAP 200 DR User Manual - English - 16 pages

Naim NAP 200 DR User Manual - German - 44 pages

Naim NAP 200 DR User Manual - French - 44 pages

Naim NAP 200 DR User Manual - Italian - 46 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info