707505
13
Zoom out
Zoom in
Previous page
1/16
Next page
E11
NAP 100
16. NAP 100 Installation and Operation
The NAP 100 should be installed on a dedicated equipment stand intended for the purpose and should be in its nal location
before connecting cables or switching on. Make sure that the amplier location allows adequate ventilation. Switch on the
source and preamplier components, with the volume turned down, before switching on the NAP 100. The NAP 100 power
switch is located on the rear panel.
16.1 General Connections Notes
The mains earth grounds only the case and the electrostatic
screen within the transformer and is not connected to the
signal negative. The mains earth must always be connected
to “ground” regardless of any other equipment used. In
order to avoid hum-loops the signal negative of the whole
system should be connected to the mains earth in one place.
The DIN and RCA signal input sockets are connected in
parallel and should not be used simultaneously.
16.2 Protection Notes
Once installed the NAP 100 is intended to remain
permanently switched on via its rear panel switch. If the
internal heatsink reaches 70°C due to prolonged operation
at high volume levels, the power amplier circuit will be
disabled until the temperature has fallen. This may take up
to thirty minutes.
OPERATION OF THE AMPLIFIER’S THERMAL PROTECTION
SUGGESTS PROLONGED USE AT TOO HIGH A VOLUME
LEVEL. YOUR LOUDSPEAKERS MAY BE AT RISK IF THIS IS
THE CASE. THE VOLUME SHOULD BE REDUCED.
16.3 Loudspeaker Cable and Connectors
A stereo set of speaker connection sockets is provided on
the rear panel. Custom Naim Audio loudspeaker connectors
are supplied to make the connection and in order to comply
with current European safety regulations these should
always be used. Naim Audio speaker cable will provide the
best results; however, a wide range of speaker cable types
can be used without risk of damage to the amplier.
Ensure when connecting speakers that they are “in phase.
That is, the positive and negative connection orientation at
both the speaker and amplier ends of the cable is the same
for both channels.
17. NAP 100 Connections
17.1 NAP 100 Rear
ch1
nc
Input
Ch1 & Ch2
ch2
-ve
DIN:
Phono:
DIN + Phono:
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Naim NAP 100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Naim NAP 100 in the language / languages: English as an attachment in your email.

The manual is 1,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Naim NAP 100

Naim NAP 100 User Manual - German - 16 pages

Naim NAP 100 User Manual - Dutch - 16 pages

Naim NAP 100 User Manual - French - 16 pages

Naim NAP 100 User Manual - Italian - 16 pages

Naim NAP 100 User Manual - Polish - 16 pages

Naim NAP 100 User Manual - Spanish - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info