707517
11
Zoom out
Zoom in
Previous page
1/24
Next page
E9
NAC 282, NAC 202 & NAC 152 XS
10 NAC 282, NAC 202 and NAC 152 XS
Introduction and Installation
The NAC 282, NAC 202 and NAC 152 XS preamplifiers do not incorporate an internal power
supply but must be used in conjunction with either a Naim power amplifier incorporating
a preamplifier power output, or with an appropriate Naim power supply. The NAC 282 is
however supplied with a NAPSC power supply that provides power to its display and control
circuits. Diagrams 12.1 to 12.5 illustrate a variety of power supply connections and options.
The preamplifier and power supply, which may be a Naim power amplifier, should be installed
on a dedicated equipment stand intended for the purpose. Do not stand either directly on top
of another item of equipment. Care should be taken to ensure that the equipment stand is
level.
The preamplifier and power supply should be installed in their final locations before
connecting cables or switching on. Ensure that the preamplifier volume is turned down before
switching on.
The following paragraphs describe installation features and functions specific to the NAC 282,
NAC 202 and NAC 152 XS. Operational features common to all preamplifiers are described in
Section 14.
10.1 NAC 282
Source Inputs and Record Outputs
The NAC 282 provides both input and record output selection
buttons arranged in two banks on its front panel.
The input selection buttons are arranged along the upper bank
and select the source signal to be routed to the power amplifier
and the loudspeakers. Below them, in the lower bank, are a
corresponding array of buttons which select the signal to be
routed to the NAC 282 record outputs.
These separate source and record sections enable one source
(a CD player, for example) to be heard whilst the output from
another (say, the tuner) is simultaneously selected for recording.
Note: It is possible to lock the record controls and prevent
accidental de-selection during recording. Record-lock is
switched on or off by pressing the source mon button four times
within six seconds.
10.2 NAC 282 and NAC 202
Input Socket Assignment
The input selection buttons select the source input signal to be
routed to the power amplifier and the loudspeakers.
The NAC 282 and NAC 202 have six DIN input sockets and
two alternative pairs of RCA Phono sockets. The RCA Phono
sockets can be assigned individually to the cd and aux 2 input
buttons in place of the DIN sockets.
Input assignment setup is accessed through preamplifier
program mode. To switch into (or exit from) program mode
press and hold the prog key on the remote handset (with the
handset in preamplifier mode). Program mode is indicated by a
flashing indicator on the front panel volume control and, on the
NAC 282, the record selection button indicators extinguishing.
Note: If no function is operated within five minutes of entering
program mode the preamplifier will return to normal mode
automatically.
Once in program mode press and hold the remote handset
1 key to select or de-select the RCA Phono socket input for
cd, and the remote handset 6 key to select or de-select the
RCA Phono socket input for aux 2. The corresponding front
panel input buttons can similarly be used to select or de-select
the RCA Phono socket inputs. The appropriate input button
indicator will flash three times on selection of the RCA Phono
option and once on selection of the DIN option.
To exit from program mode press and hold the prog key on the
handset until the record select indicators are restored and the
volume indicator stops flashing.
10.3 NAC 282 and NAC 202 Record Mute
At times when the NAC 282 or NAC 202 record outputs are not
required it is good practice to mute them in order to minimise
power consumption and maximise sound quality.
10.3.1 NAC 282 Record Mute
To engage the NAC 282 record mute simply press the record
(lower) bank front panel mute button.
10.3.2 NAC 202 Record Mute
To engage or disengage the NAC 202 record mute press the
front panel mon button followed by the front panel mute
button. The mute button indicator will illuminate when record
mute is engaged and extinguish when it is disengaged. Record
mute can also be engaged and disengaged from the remote
handset using the mon and mute keys.
Operational features
common to all
preamplifiers are
described in Section 14
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Naim NAC 552 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Naim NAC 552 in the language / languages: English as an attachment in your email.

The manual is 3,01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Naim NAC 552

Naim NAC 552 User Manual - English - 12 pages

Naim NAC 552 User Manual - German - 24 pages

Naim NAC 552 User Manual - Dutch - 24 pages

Naim NAC 552 User Manual - French - 24 pages

Naim NAC 552 User Manual - Italian - 24 pages

Naim NAC 552 User Manual - Polish - 24 pages

Naim NAC 552 User Manual - Spanish - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info