Manual NAD VISO TWO (page 22 of 34) (English)

602923

Zoom out

Zoom in

1/34

LISTENING TO AM/FM RADIO

The VISO TWO’s internal AM/FM tuner oers very high quality sound

from radio broadcasts. The reception and sound quality will always be

dependent to a degree however on the type of antenna(s) used as well as

proximity to the broadcast origin, geography and weather conditions.

ABOUT ANTENNAS

The supplied ribbon-wire FM antenna can be connected to the rear-panel

FM-antenna input using the included ‘balun’ adapter and should be fully

extended to form a “T”. This folded-dipole antenna will usually work best

when oriented vertically, with the arms of its “T” fully outstretched and

arranged perpendicular to the origin of the desired broadcast. There are

no ‘rules,’ however, and experimenting freely with antenna placement and

orientation may yield the clearest sound and lowest background noise.

In areas of poor FM reception, an exterior FM antenna can improve

performance dramatically. If radio listening is important to you, consider

consulting an antenna installation professional to optimize your system.

The supplied AM ‘loop’ antenna will usually provide adequate reception.

However, an exterior AM antenna can be used to improve reception.

Consult an antenna professional for more information.

ASSEMBLING THE LOOP ANTENNA

1 Rotate the outer frame of the antenna.

2 Insert the bottom edge of the outer frame into the groove on the stand.

3 Extend the antenna cord.

SELECTING A TUNER BAND

To select the VISO TWO’s tuner mode, rotate “INPUT SELECTOR” knob on the

front panel until AM/FM mode or the HTR 6’s numeric ‘5’ while at AMP device

selector page. Toggle [AM/FM/DB] button to select AM (or FM) mode.

Press [TUNE / ] on the front panel momentarily to step up or down

AM or FM frequencies.

Press and hold [TUNE / ] for more than 2 seconds to search up or

down AM or FM frequencies - the VISO TWO’s tuner will stop at the next

suciently strong signal it encounters. Pressing the [TUNE / ]

during the search process will stop the search.

DIRECT TUNING

If you know your desired station’s frequency allocation, you can tune

directly to the station.

1 Toggle [ENTER] button to switch between “Preset” and “Tune” mode (see

the lower line of the VFD). Select “Tune” mode.

2 Using the numeric keys of the remote control, key-in the frequency

allocation of the station. For example, to enter 104.50MHz, press “1”, “0”,

“4”, “5” and “0” or press “”1”, “0”, “4” and “5”.

NOTE

 Ensurethatthe“DEVICESELECTOR”settingofyourHTR6issetto

“TUNER”.

SETTING RADIO PRESET

The VISO TWO can store as many as 60 (30 FM and 30 AM stations) of your

favorite radio stations for immediate recall.

1 To store a radio preset, rst tune the desired frequency (see above), then

press the front panel [MEMORY] button. The VFD will show a blinking

“MEMORY” icon and the next available vacant Preset number.

2 Press [MEMORY] button again to store the desired frequency on the

Preset number shown or use the [ / ] keys to select another

available Preset number.

3 Then, press [MEMORY] key button again. Your desired frequency is now

stored in the assigned presets.

The Radio Presets must be stored from the front panel. This setup function

is not accessible from the HTR 6 remote control.

Use the [ / ] keys on the front panel to step up or down between

presets. Press and hold [ / ] to “scroll” continuously up or down. The

HTR 6 remote’s [PRESET ] keys work similarly. Empty presets will be

skipped during preset tuning.

DIRECT RECALL OF A PRESET

You can directly recall a desired Preset number.

1 Toggle [ENTER] button to switch between “Preset” and “Tune” mode (see

the lower line of the VFD). Select “Preset” mode.

2 Using the numeric keys of the remote control, directly key-in your

desired Preset number. For example, to enter Preset 5, press “5”.

NOTE

 Ensurethatthe“DEVICESELECTOR”settingofyourHTR6issetto“TUNER”.

AUTOMATIC PRESET

Preset stations may also be programmed automatically for the entire FM (or

AM) band.

1 Toggle the [AM/FM/DB] button to select FM (or AM) band.

2 Press and hold the [MEMORY} button until the station frequency

indication begins to increase.

3 Release the button and note that the tuner will search the entire FM (or

AM) band, and stop briey at each station that has acceptable signal

strength. The VISO TWO will automatically assign a preset number to

each station, and then search for the next station. Up to 30 of the best

received FM stations (or AM stations) will be automatically stored.

DELETING A STORED PRESET

You can empty a preset by deleting the stored information.

1 Select the preset number to be entered.

2 First press the [DISPLAY] button and hold it in. While holding in the

[DISPLAY] button, press the [MEMORY] button for about half a second,

then release the [MEMORY] button.

3 The preset will then be deleted and “DELETED” scrolls on the display.

4 To clear all the presets at the same time, repeat step 2 again but this

time do not release the [MEMORY] button. Hold down both buttons

until the current preset number shown in the VFD is extinguished. All

presets are now deleted.

OPERATION

USING THE VISO TWO  AM/FM/DB/iPod

ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of NAD VISO TWO in the language / languages: English as an attachment in your email.

The manual is 2,44 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of NAD VISO TWO

NAD VISO TWO User Manual - German - 34 pages

NAD VISO TWO User Manual - Dutch - 34 pages

NAD VISO TWO User Manual - French - 36 pages

NAD VISO TWO User Manual - Italian - 34 pages

NAD VISO TWO User Manual - Swedish - 34 pages

NAD VISO TWO User Manual - Spanish - 34 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

NAD VISO TWO Manual

Product: