Manual NAD T 758 (page 24 of 42) (English)

745046

Zoom out

Zoom in

1/42

SPEAKER CONFIGURATION

Every surround-sound system requires “bass-management” to direct low-

frequency content from any or all channels to the speakers best able to

reproduce it. For this function to operate correctly, it is important that you

correctly identify your speakers’ capabilities. We use the terms “Small” and

“Large” (and “O”) but note that physical size may be irrelevant.

• A “Small” speaker is any model, regardless of physical size, that lacks

signicant deep-bass response, that is, below about 200 Hz.

• A “Large” speaker is any full-range model; that is, one with deep-bass

response

• An “O” speaker is one that is not present in your system. For example,

you might not have any surround-back speakers installed; in that case,

you would set the “Back” setup item to “O”.

The Speaker Conguration is “global”; that is, it remains in force with all inputs

and in all listening modes. However, speaker settings are part of the T 758’s

Preset system. Consequently, multiple speaker settings can be stored for easy

recall as dierent types of recordings or listening modes require.

Speaker Conguration can be managed and adjusted by pressing a

combination of [ S ] and then [ D/F] keys. Set “Front”, “Center” and

“Surround” to “Large”, “Small” or “O” as your subsystem’s speakers require.

The “Back” speakers can either be one or two speakers. Set “Back” to either 1 or 2

speakers as per availability. Set “Subwoofer” to “On” or “O,” selecting “On” only if

you have a subwoofer connected to the T 758’s SUBW output jack.

ENHANCED BASS

When the subwoofer is set to ON and “Front” is set to “Large”, Enhanced

Bass is also available. Normally, with speakers set to “Large” the subwoofer

is not active. The Enhanced Bass option allows full range operation of

the speakers with the additional bass contribution of the subwoofer. This

feature is particularly useful when one wants to experience maximum

bass output. Please note that due to acoustic cancellation eects, the bass

response may be uneven when using this setting

You can set Subwoofer to “On” even with “Large” front speakers, in which

case bass content from any channels set to “Small” will be routed to both

the subwoofer and to the front speakers; LFE-channel signal will pass only

to the sub. In most subwoofer-equipped systems, setting front speakers to

“Small” is usually the better option.

All the speakers’ low frequency content can be directly adjusted within the

range 40Hz to 200Hz.

NOTE

The congurations set forth at “Speaker Setup” are carried over

whenever it is enabled during A/V Presets setting. Please see also the

section “AV Presets” for reference.

SPEAKER LEVELS

Adjusting the relative balance of your system’s loudspeakers ensures that

surround-sound recordings, whether music or lm, will present the balance

of eects, music, and dialog that the artists intended. Additionally, if your

system incorporates a subwoofer, it establishes a correct relationship

between the volume of the subwoofer and the other speakers, and thus of

low-frequencies (bass) to other sonic elements.

USING AN SPL METER

It is quite practical to perform the T 758 level setup routines “by ear,” and

careful work will produce acceptably accurate results. However, the use

of an inexpensive sound-pressure level (SPL) meter, such as Radio Shack

part number 33-2050, makes this task easier, more accurate and more

repeatable. Ownership of such a meter could prove a valuable audio tool.

The SPL meter should be placed at the primary listening position, at

approximately the height of the seated listener’s head. A tripod is helpful but

with a little duct tape almost anything - a pole lamp, music-stand, or ladder-

backed chair, for example - can do as well. Just be sure that no large acoustically

reective surfaces obstruct or are near the microphone element.

Orient the meter with its microphone (usually at one end) pointing straight

up toward the ceiling (not toward the speakers) and ensure that “C”

weighting scale is selected. Set the meter to display 75 dB SPL. On Radio

Shack meters, this necessitates either setting the meter to its 80 dB range

and taking your readings at the -5 point or selecting the 70 dB range and

reading at the +5 point.

SETTING SPEAKER LEVELS AT TEST MODE

While at “Speaker Levels” menu, press the AVR 4 remote’s [TEST] key

activating the T 758’s Speaker Levels balancing test signal. You will hear

a “surf” sound as you step through your speakers (“test” appears to the

right side of the current speaker), beginning with the Front Left. If you do

not hear the test signal, check your speaker connections or your “Speaker

Conguration” OSD menu settings.

Use the remote’s [ D/F ] keys to adjust the loudness of the noise output

from the currently playing channel to the required level (it’s usually

simplest to begin with the Front Left). As you cycle the test signal around

the speakers, the OSD will highlight the currently playing channel. The

“level oset” reading on the right will change by 1 dB increments; ±12 dB

adjustment is available. Press [ENTER] to adjust the next speaker.

NOTE

If you are balancing levels “by ear”, choose one speaker - usually the

center - as a reference and adjust each of the others in turn to “sound as

loud” as the reference. Be sure that you remain in the primary listening

position while balancing all channels.

OPERATION

USING THE T 758  SETUP MENU

ENGLISH PORTUGUÊSFRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of NAD T 758 in the language / languages: English as an attachment in your email.

The manual is 5,53 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of NAD T 758

NAD T 758 User Manual - German - 42 pages

NAD T 758 User Manual - Dutch - 42 pages

NAD T 758 User Manual - French - 44 pages

NAD T 758 User Manual - Swedish - 42 pages

NAD T 758 User Manual - Spanish - 42 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

NAD T 758 Manual

Product: