493495
15
Zoom out
Zoom in
Previous page
1/44
Next page
ALTERNATE IR CHANNEL
The T 757 has the capability to operate via Alternate IR channel. This is
practically useful if you have two NAD products that can be operated by
similar remote control commands. With alternate IR Channel, two dierent
NAD products can be controlled independently in the same zone by
setting each one to a dierent IR channel.
IR CHANNEL ASSIGNMENT
The T 757 and the AVR 4 remote control must be set to the same channel.
To change the Main Zone IR Channel on the T 757
• Press and hold SOURCE and then toggle STANDBY button to select
desired IR Channel – the VFD will show “IR Channel 1” or “IR Channel 0”.
The default IR Channel is “IR Channel 0”.
To change the IR Channel on the AVR 4 remote control
• Include a channel number before the library code. For AVR 4, library
code “10” is the default library table for AMP” device. To select this AMP”
library table for “IR Channel 0”, retain the library code “10” (or “010”).
• If you want to load the AMP” library table on “IR Channel 1”, prex the
library code with “1” to indicate association with “IR Channel 1”. Load
then the AMP” library table using the code “110”. Repeat the same for
MP (130) and TUNER (140).
SAMPLE SETUP OF TWO NAD PRODUCTS ON THE SAME ZONE
NAD T 757 and NAD C 326BEE are both defaulted to IR Channel 0. If [OFF]
button is pressed on the AVR 4 remote control (or SR 8 remote control for
the C 326BEE), both products will go to standby mode. Press [ON] and both
products will power up from standby mode.
To prevent both products from simultaneously going in and out of standby
mode along with other common commands, set each one to a dierent
IR channel. In this setup, we will keep C 326BEE and SR 8 remote control
defaulted to “IR Channel 0”. As for T 757, we will assign it to “IR Channel 1”;
the same applies to AVR 4.
Set T 757 and AVR 4 to “IR Channel 1” via the following procedure.
T 757
• Press and hold SOURCE and then toggle STANDBY button to
select “IR Channel 1”.
AVR 4
• Press and hold [AMP] in the DEVICE SELECTOR section of the AVR 4.
• While holding down the device button [AMP], press “1”, “1” and “0”
using AVR 4’s numeric buttons.
• Press [ENTER] while still holding down the device button [AMP]. The
AMP device selector will ash once to indicate that the library input
is successful.
With both T 757 and AVR 4 set to “IR Channel 1”, the C 326BEE can now be
remotely controlled independent of the T 757.
NOTE
Performing a Factory Reset for T 757 or AVR 4 will result to a return to the
factory default “IR Channel 0” setting.
IDENTIFICATION OF CONTROLS
AVR 4 REMOTE CONTROL
15
ENGLISHPORTUGUÊS FRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for NAD T 757 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of NAD T 757 in the language / languages: English as an attachment in your email.

The manual is 3,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of NAD T 757

NAD T 757 User Manual - German - 44 pages

NAD T 757 User Manual - Dutch - 44 pages

NAD T 757 User Manual - French - 44 pages

NAD T 757 User Manual - Italian - 44 pages

NAD T 757 User Manual - Portuguese - 44 pages

NAD T 757 User Manual - Swedish - 44 pages

NAD T 757 User Manual - Spanish - 44 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info