606564
13
Zoom out
Zoom in
Previous page
1/32
Next page
1313
1313
13
ENGLISH
REAR PANEL
NOTE: The T 754s component-video inputs and outputs are fully wide-band, compatible with all HDTV formats. The T 754 does not display its
on-screen menus on its component-video output. To use on-screen menus, you will need to make an S-Video or composite connection between
the T 754 and the monitor/TV, and select it for menu display.
8 DIGITAL IN OPT 1-2; COAX 3-6: Connect to the coaxial S/PDIF-format digital outputs of sources such as CD or DVD players, HDTV or satellite
tuners, or other components; connect DIGITAL IN OPT1-2 to optical S/PDIF-format digital outputs.
DIGITAL OUT: Connect the optical and/or coaxial DIGITAL OUT ports to the corresponding S/PDIF digital input of a recording component such as
a CD recorder, DAT deck, or computer soundcard. See "Setting Up the T 754".
9 POWER: Press in to switch the A/V Receiver to standby mode. Pressing POWER again turns the unit OFF, recommended if you do not plan to use
your A/V Receiver for an extended period of time. It is usual (and perfectly acceptable) to leave the T 754 in Standby mode in between normal
viewing and listening sessions.
10 SWITCHED AC OUTLET: This convenience jack can supply switched power to another component or accessory. It is powered on and off by the
front panel POWER SWITCH (or the HTR2’s [On] and [Off] keys).
NOTE: The total draw of all devices connected to this jack must not exceed 120 watts.
11 AC POWER INLET: Connect to the supplied IEC-standard removable AC power cord or a compatible cord.
12 SPEAKERS A & B: Connect the left and right front, centre, left and right surround, and surround back speaker outputs to the corresponding
loudspeakers. Each output’s “+” (red) terminal and “-“ (black) terminal must be connected to the corresponding “+” and “-“ terminals of the
loudspeaker. Use extra care to ensure that no stray wires or strands cross between posts or terminals at either end.
Connect Speakers B left and right speaker outputs to the corresponding remote loudspeakers. When speakers B are activated the output is taken
from the front left and right channels and any signal source is converted “downmixed” to stereo as indicated in the florescent display.
NOTE: Use stranded wire of at least 16 gauge (AWG); specialized speaker cable may be valuable (consult your NAD audio specialist). Connections
to the T 754 can be made with banana plugs (US model only), or using bare wire, or pins, by loosening the terminal’s plastic nut, making a clean,
neat connection, and re-tightening carefully (use the transverse hole through the post for bare-wire or pin connections). To minimize the danger
of short-circuits, ensure that only 1/2-inch of exposed wire or pin is employed in connecting.
NOTE: This unit is designed to produce optimum sound quality when connected to speakers with impedances within the receiver’s operating
range. Please check front, center, and surround speakers are rated to be 4 min. per speaker.
IMPORTANT NOTE: For optimum surround performance, the T 754 speaker settings and levels must be set correctly via the receiver’s setup
routines; see “Setting Up the T 754”.
13 DVD, SAT, VCR, VIDEO 4, VIDEO 5: These comprise the T 754s principal inputs. Connect S-Video, composite video, and analog stereo audio from
source components such as DVD players and HDTV/satellite tuners (see "Input Setup," below). VCR and VIDEO 4 may be used with recording
components such as videocassette or DVD-recorders; connect the T 754 S-Video/composite video OUT jacks to these components’ record-inputs.
(Note that VCR/VIDEO 4 may freely be used for play-only components, in which case their OUT jacks would remain unconnected.)
14 MAIN IN/AUDIO PRE-OUTS/SUBWOOFER OUT: The T 754s six built-in power amplifier channels will deliver excellent quality with even very
demanding, low sensitivity home-theatre speaker systems. However, it is also possible to use the T 754 as a pre-amplifier with external power
amplifiers for some or all channels (remove the supplied jumpers) if necessary. Unlike the six full range channels, there is no power amplifier built-
into the T 754 for a subwoofer.
Connect the SW output 1, 2 or both to powered (“active”) subwoofers (or to power amplifier channels driving a passive system).
SURR-BACK-R jack will supply the same signal from the surround-back Left channel if the T 754 is so configured (see “Speaker Setup,” below).
Either one or both channels are available mono or stereo as per “Speaker Setup”. Connect to one or two channels of an appropriate external
power amplifier or other amplified component to furnish amplification for one or two surround back speakers. Your NAD audio specialist will be
happy to advise you.
NOTE: Never connect the T 754s speaker outputs and the speaker outputs of an external amplifier to the same speakers.
15 TAPE IN/OUT: Connect the T 754s TAPE OUT jacks to the stereo analog audio inputs, of an audio recording component such as a cassette deck
or CD recorder, or of an outboard analog audio processor such as a stereo equalizer; connect the receiver’s TAPE IN jacks to the component’s
corresponding outputs.
NOTE: Digital input signals are not available at the analog TAPE OUT jacks.
16 MS OUT (MULTISOURCE OUT): Connect this pre-amp outputs to other zones using high-quality patch cables to reduce noise pickup over long
distance runs.
17 7.1 CH. INPUT: Connect to the corresponding analog audio outputs of a multichannel source component such as a DVD-Audio or multichannel-
SACD player, or external multichannel decoder. Typically, these sources will produce 5.1-channel output, in which case the SURROUND BACK jacks
are left unconnected. The signals present at these jacks may be heard by selecting the front-panel EXT. 7.1 key or the HTR 2’s [Ext 7.1/5.1]
button. See “Selecting Sources".
NOTE: There is no bass-management or other processing (other than master-volume control) available to this 7.1 CH. INPUT. While the multi-
channel audio outputs of a DVD-Video player can be connected to these jacks, using the T 754s own Dolby Digital and DTS decoding and digital-
analog converters, via a digital connection, will usually produce superior results.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for NAD T 754 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of NAD T 754 in the language / languages: English as an attachment in your email.

The manual is 1,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of NAD T 754

NAD T 754 User Manual - German - 32 pages

NAD T 754 User Manual - Dutch - 32 pages

NAD T 754 User Manual - French - 32 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info