602914
10
Zoom out
Zoom in
Previous page
1/20
Next page
10
ENGLISH FRANÇAIS
DEUTSCH
NEDERLANDS
ESPAÑOL
ITALIANO
PORTUGUÊS
SVENSKA
FRONT PANEL CONTROLS (FIGURE 1)
1. Standby Button: The Standby Button turns on and to standby the M3. This button will
only function when the Status Condition LED is either blue representing the on-state, or
amber representing the standby state.
2. Status Condition L.E.D.:
Standby: When this L.E.D. is amber the M3 is in the standby state.
On: When this L.E.D. is blue the M3 is operating in the on-state.
Protection: When this L.E.D. is red the M3 is in a protection state.
The M3 has sensors for abnormally high internal heat and signal level conditions that
would damage either the M3 or speakers. When these conditions return to normal, the
M3 reverts to the on-state. In the event the Status Condition L.E.D. is red and PROTECT
displays in the VFD for longer than 5 minutes; switch off the M3 via the rear panel POWER
switch, check all speaker cables and connections for short-circuits. Resume normal
operation. If the Status Condition L.E.D. continues to light red and PROTECT displays in
the VFD, contact qualified NAD service personnel for repair.
3. Vacuum Florescent Display (VFD): The VFD provides visual information on all of the
M3's important modes, settings, and functions for both main and second zone locations.
4. listen (input selection): Press the listen button to select an input. A press longer than
one second will advance the input selection to the next input as follows; DISC, CD, TUNER,
INPUT 4, INPUT 5, INPUT 6, BALANCED and then return to DISC. Release the listen button
to stop the sequence.
Assigning User Names (input selection): Renaming inputs is advantageous when using
auxiliary equipment not representing the default inputs. For example, a CD-player with
balanced outputs would connect to the balanced input. Rename the balanced input to
CD-Player as follows;
Press and hold simultaneously the listen and record / Z2 buttons until the cursor flashes.
Rotate the volume (set up) control to the letter "C" then press the listen button to lock
the selection and advance the cursor. Continue the procedure for the remaining letters of
the name. Press the record / Z2 button to save the new user name.
NOTES: There is a maximum of 20 letters to each name. The variables are; lowercase letters,
uppercase letters, numbers, and miscellaneous punctuation symbols.
Record each name you assign into the chart on page 17 to aid you for future reference in
the event you wish to change the hook-up and assignment of the inputs.
5. record / Z2 (second zone output): Press the record / Z2 button to select the input as
the recording source. A press longer than one second will advance the source selection to
the next input as follows; OFF, DISC, CD, TUNER, INPUT 4, INPUT 5, INPUT 6, BALANCED,
LOCAL, and then return to OFF. Release the record / Z2 button to stop the sequence.
Furthermore, the ZR3 remote control will allow direct selection of inputs (see ZR3 Remote
Control).
NOTE: The record / Z2 can monitor all inputs. The record / Z2 will maintain its last state even
if the M3 is set to standby. The M3 must be in its on state in order to use the record / Z2.
About the M3 Dual Mono Integrated Amplifier:
Identification of controls
M3 10262005.qxd 1/3/2006 2:49 PM Page 10
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for NAD M3e at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of NAD M3e in the language / languages: English as an attachment in your email.

The manual is 1,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of NAD M3e

NAD M3e User Manual - German - 20 pages

NAD M3e User Manual - Dutch - 20 pages

NAD M3e User Manual - French - 20 pages

NAD M3e User Manual - Italian - 20 pages

NAD M3e User Manual - Portuguese - 20 pages

NAD M3e User Manual - Swedish - 20 pages

NAD M3e User Manual - Spanish - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info