562261
15
Zoom out
Zoom in
Previous page
1/38
Next page
SETUP MENU
The Setup Menu allows one to customize the operation of the M17 to the
ancillary equipment used in one’s specic AV system. Unless your system
exactly matches the factory defaults as shown in the accompanying Quick
Setup Guide, you will need to use the setup menu to congure the inputs
of the M17.
At Setup Menu, the following are congurable – Control Setup, Source
Setup, Speaker Setup, Zone Setup, Trigger Setup, Listening Mode Setup,
Display Setup and A/V Presets.
To access and navigate through Setup Menu and its sub-menu selections,
please follow the directions stated in the sections “DISPLAY THE OSD” and
“NAVIGATING THE OSD AND MAKING CHANGES”.
CONTROL SETUP
The M17 supports HDMI Control (CEC) and Audio Return Channel (ARC)
functions. Both functions are possible if external devices that also support
both features are interconnected with the M17 via HDMI connection.
AUTO STANDBY
On: M17 will go to standby mode automatically if there is no user
interface interaction within 30 minutes.
O: M17 remains active even if there is no user interface interaction is
detected.
ETHERNET/CEC IN STANDBY
O : M17 will not pass through any CEC message. Audio and video will not
be streamed from a CEC-enabled HDMI source to a CEC-enabled TV (with
both devices connected via M17). CEC feature is eectively defeated.
On: Enable HDMI Control (CEC) feature. Audio and video will continuously
stream from a CEC-enabled HDMI source to a CEC-enabled TV (with both
devices connected via M17).
Ethernet connection is established when the NAD AVR Remote App is
activated and connected to the same network as the M17. Under this
condition, “Ethernet/CEC in Standby will automatically turn from “O
to “On, will remain “On” and cannot be changed from “On to “O. The
On/O options of “Ethernet/CEC in Standby can be selectable again by
deactivating or disconnecting the NAD AVR Remote App from the network.
HDMI CONTROL CEC
Consumer Electronics Control (CEC) is a set of commands that utilizes
HDMI’s two- way communication to allow for single remote control of any
CEC-enabled devices connected with HDMI. A CEC command will trigger
the necessary commands over HDMI for an entire system to auto-congure
itself to respond to the command.
When devices that support HDMI Control (CEC) are connected, the
following modes of operation can be executed via the M17 or the external
device using any of the device’s remote control.
O: Applies to all CEC options below. At “O setting, particular CEC feature
is defeated.
Power: At “On setting, the M17 will automatically go to standby mode
if it receives a CEC standby command. On the other hand, if the M17
receives a CEC power up command, the M17 will correspondingly
switch ON from standby mode.
Source Switch: At “On” setting, the M17 will automatically switch
sources if another CEC device requests a Source change.
For example, if PLAY is pressed on a BD Player with CEC, the M17 and TV
with CEC will automatically switch to their respective input connections
- the M17 switching to the HDMI input where the BD Player is
connected while the TV will switch to its input where the M17’s HDMI
MONITOR OUT is connected. This completes the auto-conguration -
the BD Player is automatically played back using the M17 and TV.
Audio System: At “On setting, the M17 will broadcast a CEC message
indicating it is an active audio system. A CEC compatible TV will usually
mute its audio output when this happens. When this option is enabled,
the M17 will also respond to CEC volume and mute commands. For
example, a CEC TV may forward the volume commands from its remote
to the M17.
ARC Mode: Audio Return Channel (ARC) enables an ARC-enabled TV
to send audio data upstream” to M17.
This option has three choices: O, Auto or Source Setup.
Auto: When set to Auto, the M17 will automatically attempt an ARC
audio connection to the TV whenever the TV announces over CEC
that it has become the active source. If an ARC connection can be
established, the M17 will output the ARC audio signal no matter
what source is selected on the M17. The Auto option tends to work
best when all your devices support CEC and the Source Switch
option is set to On.
Source Setup: When set to Source Setup, you can select ARC for
the digital audio input in the source setup screen. When you select
a source on the M17 which is set for ARC, the M17 will attempt to
initiate an ARC connection with the TV. When using this option,
you would probably also want to make sure Source Switch is o
otherwise other CEC devices may keep changing the M17 source
when you want it to remain on the ARC source.
IMPORTANT NOTES
Audio System” must be set to “On” for “ARC mode” to manifest as an
option.
Audio and video will continuously stream from the HDMI source with
CEC to the TV with CEC even if the M17 is at standby mode.
OPERATION
USING THE M17  SETUP MENU
15
ENGLISHFRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for NAD M17 AV at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of NAD M17 AV in the language / languages: English as an attachment in your email.

The manual is 7,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of NAD M17 AV

NAD M17 AV Quick start guide - English - 2 pages

NAD M17 AV User Manual - German - 38 pages

NAD M17 AV User Manual - Dutch - 38 pages

NAD M17 AV User Manual - French - 38 pages

NAD M17 AV User Manual - Italian - 38 pages

NAD M17 AV User Manual - Swedish - 38 pages

NAD M17 AV User Manual - Spanish - 38 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info