667813
6
Zoom out
Zoom in
Previous page
1/22
Next page
1 o (STANDBY)
Press o (Standby) button for the M12 to be switched ON from
standby mode. The Power indicator will turn from amber to bright/
white color.
Pressing o (Standby) button again switches back M12 to standby
mode. The Power indicator will illuminate to amber color at standby
mode.
The o (Standby) button cannot activate the M12 with the rear
panel POWER switched o.
IMPORTANT NOTES
Refer also to +12V TRIGGER (IN/OUT) in IDENTIFICATION OF CONTROLS
– REAR PANEL.
For the o (Standby) button to activate, two conditions must be
completed.
a. Plug-in the supplied mains power cord to a mains power source.
Connect corresponding end of the mains power cord to the AC
mains input of M12 and the plug connected to a mains power
source.
b. The rear panel POWER switch must be set to ON position.
2 POWER INDICATOR
This indicator will light up amber when the M12 is at standby mode.
When the M12 is powered up from standby mode, this indicator
will turn from amber to bright/white color.
3 REMOTE SENSOR
Point the HTRM 2 remote control at the remote sensor and press
the buttons.
Do not expose the remote sensor of the M12 to a strong light
source such as direct sunlight or illumination. If you do so, you may
not be able to operate the M12 with the remote control.
Distance: About 23ft (7m) from the front of the remote sensor.
Angle: About 30° in each direction of the front of the remote sensor.
4 DISPLAY (TOUCH PANEL DISPLAY)
Show visual and menu information according to the display
settings selected.
The following display options are accessible via the touch panel
display - Main, Media, Mode, EQ and Setup.
Use your nger to press and select any of these display options to
show their corresponding menu options or settings.
5 VOLUME
The VOLUME control adjusts the overall loudness of the signal being
fed to the loudspeakers. Volume control is characterized by perfect
signal tracking and channel balance. It gives a highly linear and low
noise operation.
Turn clockwise to increase the volume level; counter clockwise to
lower it.
The default volume level is -20dB.
6 DIGITAL USB FRONT
Connect a USB mass storage device to this input. Typical USB
mass storage devices compatible with M12 include portable ash
memory devices and external hard drives (FAT32 formatted).
Refer also to the item about LISTENING TO USB DEVICE at the
OTHER FEATURES section of the OPERATION page.
IDENTIFICATION OF CONTROLS
FRONT PANEL
© NAD M12
M12
DIGITAL PREAMP DAC
4 652 3
1
6
ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for NAD M12 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of NAD M12 in the language / languages: English as an attachment in your email.

The manual is 3,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of NAD M12

NAD M12 User Manual - German - 22 pages

NAD M12 User Manual - Dutch - 22 pages

NAD M12 User Manual - French - 22 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info