745038
7
Zoom out
Zoom in
Previous page
1/14
Next page
ENGLISH
9 LAN/USB
LAN
LAN connection must be setup for wired connection to be
established. Set up a Wired Ethernet broadband router with
broadband internet connection. Your router or home network
should have a built-in DHCP server to consummate the connection.
Using a standard straight-through Ethernet cable (not supplied),
connect one end of the Ethernet cable to the LAN port of your wired
Ethernet broadband router and the other end to M10’s LAN port.
NOTES
NAD is not responsible for any malfunction of the M10 and/or the
internet connection due to communication errors or malfunctions
associated with your broadband internet connection or other
connected equipment. Contact your Internet Service Provider (ISP) for
assistance or the service bureau of your other equipment.
Contact your ISP for policies, charges, content restrictions, service
limitations, bandwidth, repair and other related issues pertinent to
internet connectivity.
USB
Connect to this USB port USB mass storage devices formatted as
FAT32, NTFS or Linux ext4. The connected USB device appears as a
Local Source (USB) in the BluOS App.
Access and playback music stored in the connected USB device by
selecting “USB from the BluOS App.
10 STANDBY BUTTON
Press Standby button to switch ON the M10 from standby mode.
The Status indicator will change from amber to solid white.
Switch back M10 to standby mode by holding down Standby
button until the NAD logo indicator starts ashing red before
turning to solid amber.
11 AC MAINS INPUT
The M10 comes supplied with two separate mains power cords.
Select the mains power cord appropriate for your region.
Before connecting the power cord’s plug to the mains power outlet,
ensure that the other end of the power cord is rmly connected to
M10’s AC Mains input socket..
Always unplug the power cord from the mains power outlet before
disconnecting the other end of the power cord from M10’s AC
Mains input socket.
12 BRIDGE MODE
M10 output power is at least doubled when set to Bridge Mode. This
way, the M10 can be used as part of a high power stereo or home-
theatre system by connecting additional power ampliers.
· In BRIDGE MODE (switch at ON setting), the M10 will produce
approximately 200W into an 8 ohm loudspeaker. In this mode, the
amplier sections will react as though the speaker impedance has
been halved. Low impedance speakers (under 8 ohms) are not
recommended when using Bridge Mode as these may cause the
ampliers thermal cut-out to operate if played at high levels.
· Set the BRIDGE MODE switch to “ON“ position. Then, connect the
speaker to the rear panel terminals marked “SPEAKER RIGHT +” and
“SPEAKER LEFT +” ensuring that “SPEAKER RIGHT +” is connected to
the “-” terminal of your speaker and “SPEAKER LEFT +” is connected
to the speakers “+” terminal.
· Connect the source to the Left input sockets only. Do not connect
anything to the Right Input socket when Bridge Mode is selected.
13 SPEAKERS
Connect M10’s Right speaker terminals marked “R +” and “R-” to
the corresponding “+” and “-“ terminals of your designated right
speaker. Repeat the same for M10’s Left speaker terminals and
corresponding left speaker.
IDENTIFICATION OF CONTROLS
REAR VIEW
7
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for NAD M10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of NAD M10 in the language / languages: English as an attachment in your email.

The manual is 1,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of NAD M10

NAD M10 User Manual - German - 14 pages

NAD M10 User Manual - Dutch - 14 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info