493487
9
Zoom out
Zoom in
Previous page
1/14
Next page
9 +12V TRIGGER IN: This input allows the M2 to be switched remotely
to standby mode or ON by ancillary equipment, such as an amplier,
preamp, AV processor, etc. The controlling device must be equipped
with a 12 V trigger output to use this feature.
10 +12V TRIGGER OUT: The +12V TRIGGER OUT is used for controlling
external equipment that is equipped with a +12V trigger input. This
output will be 12V when the M2 is ON and 0V when the unit is either
OFF or in standby mode.
11 RIGHT SPEAKERS: Connect the right speaker to the terminals marked
“R +” and “R-” ensuring that the “R+” is connected to the “+” terminal
on your loudspeaker and the “R-” is connected to the loudspeakers “-”
terminal. There are two sets of RIGHT SPEAKER outputs and these are
identical in function (parallel connection) and are provided for ease of
Bi-wiring with heavy audiophile cables. Double check your speaker
connections before powering up the M2.
Always use heavy duty (16 gauge; 1.5mm, or thicker) stranded wire
to connect loudspeakers to your M2. The high-current binding post
terminals can be used as a screw terminal for cables terminating in
spade or pin sockets or for cables with bare wire ends.
BI-WIRING
Most modern high quality loudspeakers oer the option of Bi-wiring.
This separates the HF crossover from the LF crossover and oers
enhanced performance by preventing LF return currents from aecting
the HF performance. If you decide to bi-wire, be sure to remove the
“links” at the loudspeaker that connect the LF and HF sections (these are
provided for convenience when single wire connection is used). Your
loudspeaker instruction manual should cover this subject as well.
WARNING
The M2 employs a “oating” ground design. External devices (such as
speaker switching or headphone adaptors) that connect the left and
right channels together must not be used with the M2. Left and right
channels must never be connected to each other.
12 POWER SWITCH: The POWER switch supplies the master AC mains
power for the M2. When this switch is at ON position, the M2 is in
standby mode as shown by the amber status condition of the standby
LED. Toggle the front panel’s STANDBY button to switch ON the M2 or
back to standby mode. If you intend not to use the M2 for long periods
of time (such as when on vacation), switch the POWER switch to the
OFF position. When the POWER switch is at OFF position, the front
panel STANDBY button or M2 remote control cannot activate the M2.
13 AC MAINS INPUT: The M2 comes supplied with a separate AC Mains
cable. Before connecting the cable to a live wall socket ensure that
it is rmly connected to the M2’s AC Mains input socket rst. Always
disconnect the AC Mains cable plug from the live wall socket rst,
before disconnecting the cable from the M2’s Mains input socket.
14 FUSE HOLDER: In the unlikely event a fuse may need to be replaced,
unplug the AC cord from the wall. Disconnect also the AC cord from
M2’s AC Mains input socket. Then, remove all connections from the
amplier. Use a athead screw or similar to open the fuse holder via the
slot located on the top edge of the fuse holder. With the screw driver
in place, push it outward to unlatch and open the fuse holder. Only
replace the fuse with the same type, size, and specication.
IMPORTANT NOTICE
Do not use any substitute fuses of dierent types, ratings or values.
Failure to observe this precaution may cause damage to the amplier
circuits and may create a re hazard and/or defeat the safety built into
the M2 thus voiding the warranty.
15 LEFT SPEAKERS: Connect the left speaker to the terminals marked “L
+” and “L-” ensuring that the “L+” is connected to the “+” terminal on your
loudspeaker and the “L-” is connected to the loudspeaker’s “-” terminal.
There are two sets of LEFT SPEAKER output and these are identical in
function (parallel connection) and are provided for ease of Bi-wiring
with heavy audiophile cables. Refer also to “RIGHT SPEAKERS” above.
16 RS-232: Connect this interface via RS-232 serial cable (not supplied)
to any Windows® compatible PC to allow remote control of the M2
through NAD’s proprietary PC software or other compatible external
controllers. NAD is a certied partner of AMX, Control4, Crestron and
Savant and fully supports these external devices. See your NAD audio
specialist for more information.
17 IR IN: This input is connected to the output of an IR (infrared) repeater
(Xantech or similar) or the IR output of another component to allow
control of M2 from a remote location.
18 GROUND TERMINAL: The M2 requires a grounded AC receptacle or a
separate earth ground. Use this terminal to properly ground your M2. A
ground lead wire or similar can be used to connect the M2 to ground
via this ground terminal. After insertion, tighten the terminal to secure
the lead.
BARE WIRES AND PIN CONNECTORS
Bare wires and pin connectors should be inserted into the hole in the shaft
of the terminal. Unscrew the terminal’s bushing until the hole in the screw
shaft is revealed. Insert the pin or bare cable end into the hole and secure
the cable by tightening down the terminal’s bushing. Avoid any danger
of bare metal from the cables touching the rear panel or another connector.
SPADE CONNECTORS
These should be slotted under the terminal’s screw bushing, which is then
fully tightened. Ensure the connector is tightly secured and there is no
danger of bare metal from spade connectors touching the rear panel or
another connector as this may cause damage.
IDENTIFICATION OF CONTROLS
REAR PANEL
9
ENGLISHFRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for NAD M 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of NAD M 2 in the language / languages: English as an attachment in your email.

The manual is 1,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of NAD M 2

NAD M 2 User Manual - German - 14 pages

NAD M 2 User Manual - Dutch - 14 pages

NAD M 2 User Manual - French - 14 pages

NAD M 2 User Manual - Italian - 14 pages

NAD M 2 User Manual - Swedish - 14 pages

NAD M 2 User Manual - Spanish - 14 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info