745047

NAD CI 980 Manual

7
Zoom out
Zoom in
Previous page
1/12
Next page
1 GLOBAL INPUT/OUTPUT
• Always turn OFF the CI 980 and other components in the system
before connecting or disconnecting anything to GLOBAL’s INPUT/
OUTPUT terminals.
• Connect the output from a pre-amplier or processor, such as a
surround-sound decoder, to the INPUT terminals. Use a twin RCA-
to-RCA lead to connect the left and right “Audio Output” of the
preamplier or processor to these INPUT terminals.
• The OUTPUT terminal is a line level “loop through” output. The
same level of input signal at the INPUT terminals is available at the
OUTPUT terminals thereby allowing the same signal to be shared or
passed on to another amplier.
• These INPUT/OUTPUT terminals are dedicated only to GLOBAL
settings.
• If the LOCAL/GLOBAL mode selector switch of a particular ZONE is
set to GLOBAL, the source connected to GLOBAL’s INPUT terminals
will become the active input for the particular ZONE.
2 GLOBAL GAIN CONTROL
• Before switching ON the CI 980 from standby mode for the rst
time, make sure all GAIN controls are set to minimum (MIN) level
position.
• This GAIN control is dedicated only to GLOBAL settings. Rotate
clockwise or counterclockwise to adjust GLOBAL's audio level with
respect to the GLOBAL source's input signal.
• Refer also to item about GAIN CONTROL (ZONE 1- 4).
3 STEREO/BRIDGE MODE SELECTOR SWITCH (ZONE 1- 4)
• Depending upon the corresponding speaker setup connection,
slide the particular Zone’s selector switch to either STEREO or
BRIDGE mode.
LOCAL/GLOBAL MODE SELECTOR SWITCH
• Slide particular Zone’s selector switch to either LOCAL or GLOBAL
depending upon the selected input. If GLOBAL is selected, the source
connected to GLOBAL’s INPUT terminals will become the active input
for the particular ZONE. On the other hand, if LOCAL is selected, the
active source at corresponding Zone’s INPUT terminals will be applied.
To illustrate, if LOCAL/GLOBAL mode selector switch of ZONE 4 is set
to GLOBAL, the input from GLOBAL’s INPUT terminals will be the active
input for ZONE 4. On the other hand, if LOCAL/GLOBAL mode selector
switch of ZONE 4 is set to LOCAL, input from ZONE 4 INPUT terminals
will be the active input for ZONE 4.
4 SPEAKER OUT (ZONE 1 - 4)
• Connect the speaker cables to the supplied speaker connector with
reference to the particular Zone’s SPEAKER OUT terminal markings in
the rear panel.
• At STEREO mode, ensure that particular Zone’s “R+” is connected
to the “+” terminal of your right speaker and “R-” connected to the
speaker’s “-” terminal. Connect the particular Zone’s SPEAKER OUT
terminals marked “L+” and “L-” to the left speaker in the same way.
STEREO MODE
SPEAKER CONNECTION
SPEAKER OUT “R”
TERMINAL
SPEAKER OUT “L”
TERMINAL
R+ R- L+ L-
Left speaker terminals + -
Right speaker terminals + -
• At Bridge Mode, connect the single speaker to the particular Zone’s
SPEAKER OUT terminals marked “R +” and “L+” ensuring that “L+” is
connected to the speaker’s “+” terminal and “R+” connected to the
speaker’s “-” terminal.
BRIDGE MODE
SPEAKER CONNECTION
SPEAKER OUT “R”
TERMINAL
SPEAKER OUT “L”
TERMINAL
R+ R- L+ L-
Speaker terminals - +
BRIDGE MODE
A particular ZONE can be congured to be MONO (Bridge mode), more
than doubling its output power. This way, a particular ZONE can be used
as part of a high power stereo or home-theatre system by connecting
additional power ampliers. In this mode, the amplier section will
react as though the speaker impedance has been halved.
At Bridged mode, ZONE 2 will produce approximately 100W into an
8 ohm loudspeaker. Low impedance speakers (under 8 ohms) are
not recommended when using Bridge mode as these may cause the
amplier’s thermal cut-out to operate if played at high levels.
IDENTIFICATION OF CONTROLS
REAR PANEL
© NAD CI980
INPUT
OUT
PUT
INPUT
OUTPUT INPUT OUTPUT INPUT OUTPUT INPUT OUTPUT
ATTENTION!
Please make sure that the CI 980 is powered OFF or unplugged before making any connections. It is also advisable to power-down or unplug all associated
components while making or breaking any signal or AC power connections.
1 2 3 4
5 6 7 8 9 10 11
7
ENGLISHFRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for NAD CI 980 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of NAD CI 980 in the language / languages: English as an attachment in your email.

The manual is 1,07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of NAD CI 980

NAD CI 980 Quick start guide - English - 2 pages

NAD CI 980 User Manual - German - 12 pages

NAD CI 980 User Manual - Dutch - 12 pages

NAD CI 980 User Manual - French - 12 pages

NAD CI 980 User Manual - Italian - 12 pages

NAD CI 980 User Manual - Swedish - 12 pages

NAD CI 980 User Manual - Spanish - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info