Manual NAD c422 (page 6 of 68) (English, German, Dutch, French, Italian, Portuguese, Swedish, Spanish)

161019

Zoom out

Zoom in

1/68

ENGLISH FRANÇAIS

DEUTSCH

NEDERLANDS

ESPAÑOL

ITALIANO

PORTUGUÊS

SVENSKA

FRONT PANEL CONTROLS

1 Power On/Off - POWER switches the tuner on or off. Pressing the

Power switch turns the Tuner on, the Display Panel and Power Status

Indicator (No. 2) will light up. Pressing the Power button again will

switch the unit off.

NOTE

The C 422 has a receiver for remote control commands built-in. Most

NAD system remote control handsets with an On/Off toggle button

or separate On and Off button will be able to switch the tuner from

On to Stand-by and vice-versa.

The C 422 uses a memory back-up system to store Preset

information. This information is retained for several weeks, even if

the unit is switched off completely or unplugged. When switching

power On, the C 422 will go back to the station last tuned to before

the unit was turned off. This will allow you to make timer recordings

using an external timer and recorder.

2 Power Status Indicator - The Power Status Indicator will light up

green when Power is on. When the tuner is switched to Stand-by

mode (through either a remote control or the 12V trigger input) the

indicator will light up amber. When the unit is switched off

completely, it is off.

3Blend - Weak or remote stereo radio stations are sometimes

received with noise and hiss as the antenna signal is too weak. By

switching the tuner to mono will reduce the amount of noise and

hiss but at the expense of any stereo information. The NAD Blend

feature will allow you to reduce the amount noise and hiss but still

retain some level of stereo separation, instead of mono. The Blend

button toggles between engaging or disengaging the Blend feature;

when engaged, "BLEND" lights up in the display.

NOTE

The "Blend" status can be stored for individual presets. Refer to the

separate chapter "Storing, Recalling and Labelling Presets" for more

information.

4 Memory - The Memory is used to store stations into the Preset

Memory bank and to store user defined names for non-RDS Preset

stations. When Memory is pressed during normal operation, the

Preset number and the red "MEMORY" indicator will flash in the

Display Panel. If no other buttons are pressed within 12 seconds, the

tuner will revert to its previous state. Refer to the separate chapter

"Storing, Recalling and Labelling Presets" for more information.

5FM Mute/Mode - This button combines two functions; it switches

the tuner from Stereo to Mono and disengages the muting circuitry

at the same time. The muting circuit will mute the tuner in between

radio stations when searching or tuning. This way the tuning noise is

avoided. The muting circuit however may suppress very weak radio

station signals. If a weak station is in stereo it will have a high level of

background hiss. Switching to Mono Mode and disengaging the

muting circuit by depressing the FM MUTE/MODE button will allow

the station to be heard and will cancel most or all of this background

noise.

In normal operation the mute circuit is engaged, the display indicates

"FM MUTE". Press the FM Mute/Mode button to disengage the

muting circuit and switch from stereo to mono reception. "FM

MUTE" in the display will extinguish. Press the FM Mute/Mode switch

again to return to Auto Stereo FM operation.

NOTE

The "FM Mute/Mode" status can be stored for individual presets.

Refer to the separate chapter "Storing, Recalling and Labelling

Presets" for more information.

6 AM/FM - The AM/FM button switches the tuner from the AM band

to the FM band and vice-versa. The Display Panel shows the

frequency of the tuned station and which band is selected. The FM

tuning is in 0.05 MHz increments, AM tuning is in 9 kHz or 10 kHz

increments, depending on the version.

7 Display - With stations carrying RDS information, The Display

button scrolls between three different display modes, each successive

push of the button engages the next one of the three modes:

a) In the default mode, the station’s RDS name is displayed, Program

Service (PS; normally the station’s calling letters, BBC R3, for

instance).

b) From the default mode, press the button once to view Radio Text

(RT). This can be additional information such as the presenter’s or

program’s name; what song is playing, etc. This text scrolls

continuously over the 8 alphanumeric display segments.

c) Press the button from the display RT mode to display the station

frequency. Press again to return to the default mode (a).

When tuned to a non-RDS station - The Display button toggles

the display to show either the station frequency or user entered

station name. If no user name was entered the display will indicate

"NO RDS". The Display button is also used to label non-RDS stations

with a name. Refer to the separate chapter "Storing, Recalling and

Labelling Presets" for more information.

C422 manual - 6 8/8/03 5:32 PM Page 6

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of NAD c422 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Swedish, Spanish as an attachment in your email.

The manual is 1,06 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

NAD c422 Manual

Product: