161218

NAD c 420 Manual

8
Zoom out
Zoom in
Previous page
1/44
Next page
GB
SETUP FOR CUSTOM
AND MULTI-ZONE INSTALLATIONS
REMOTE CONTROL CODES
The NAD C420 has a remote control command receiver built in so
it will respond to NAD remote control commands, such as from
most NAD system remote controls (RC450, RC451, S70; not
supplied with C420). This will allow access to basic functions
such as preset up/down, On/Stand-by.
Particularly with Custom Install in mind, the NAD C420 will
respond to other commands not usually found on NAD remote
control handsets. The table below indicates all commands the
C420 recognises.
The NAD C420 uses the NEC format for IR transmission; customer
code is 877C, the corresponding hex codes are next to the IR
command:
Footnote Function Hex Code
1 Preset D2
Preset D1
2 Search 87
Search 86
3 Tune D4
Tune D3
4 Preset 1 8A
Preset 2 8E
Preset 3 92
Preset 4 94
Preset 5 8B
Preset 6 8F
Preset 7 93
Preset 8 97
Preset 9 98
Preset 0 C7
5 Enter C5
6 Power/standby toggle 80
7 Power On 25
8 Stand-by C8
1) Preset and scroll trough presets, with wrap-around.
2) Search and will engage auto-searching,
with wrap-around
3) Tune and will engage tuning. if command received
for more than 1 second, auto-search is engaged; wrap around
4) Preset 1-9, 0: Allows direct entry of preset number. First send
desired number code, send Enter code to confirm. If preset is
empty, tuner will default to current status.
5) Enter: To confirm and engage preset number. Program small
macro with preset 1-9,0 and enter to gain direct preset access.
6) Power/Stand-by toggle: Switches tuner from On to Stand-by
and vice-versa. This code is also used on other remote
controlled products.
7) Power On: To avoid sync problems with other NAD products
also using the Power/Stand-by toggle, the C420 responds to
separate On code in addition; if already switched on, it will
remain on.
8) Stand-by: For same reason as above. If already in Stand-by
mode, it will remain so.
12V TRIGGER INPUT
NAD components equipped with 12V output triggers are fully
compatible with the C420’s 12V input trigger.
Plug type: 3.5mm mono mini-jack
Operating range: 6 to 15 V DC
Current drawn: <10mA
Centre pin = +
Shaft = -
NAD reserves the right to change specifications without notice.
8
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for NAD c 420 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of NAD c 420 in the language / languages: English, German, French, Italian, Portuguese, Swedish, Spanish as an attachment in your email.

The manual is 0,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info