493504
19
Zoom out
Zoom in
Previous page
1/26
Next page
IR CHANNEL
IR Channel
}~CH0
`CH1
`CH2
The C 390DD has the capability to operate over four IR channel settings.
This is practically useful if you have several NAD products that can be
operated by similar remote control commands. With varying IR Channel
settings, dierent NAD products can be controlled independently in the
same zone by setting each one to a dierent IR channel.
IR CHANNEL ASSIGNMENT
The C 390DD and the AVR 4 remote control must be set to the same
channel.
To change the IR Channel on the C 390DD
While at “IR Channel” menu, use the [D/F] to select through CH 0
to CH 3. Press [S] to select preferred IR Channel setting. C 390DD IR
Channel is defaulted to CH0.
To change the IR Channel on the AVR 4 remote control
Include a channel number before the library code. For AVR 4, library
code “10” is the default library table for AMP device. To select this AMP”
library table for IR Channel 0 (CH0), retain the library code “10” (or “010”).
If you want to load the AMP library table on ”IR Channel 1” (CH1) prex
the library code with “1” to indicate association with “IR Channel 1” (CH1).
Load then the AMP” library table using the code “110”. Repeat the same
for MP (130) and TUNER (140).
SAMPLE SETUP OF TWO NAD PRODUCTS ON THE SAME ZONE
NAD C 390DD and NAD C 326BEE are both defaulted to IR Channel 0. If
[OFF] button is pressed on the AVR 4 remote control (or SR 8 remote control
for the C 326BEE), both products will go to standby mode. Press [ON] and
both products will power up from standby mode.
To prevent both products from simultaneously going in and out of standby
mode along with other common commands, set each one to a dierent
IR channel. In this setup, we will keep C 326BEE and SR 8 remote control
defaulted to “IR Channel 0” (CH0). As for C 390DD, we will assign it to
“IRChannel 1” (CH1); the same applies to AVR 4.
Set C 390DD and AVR 4 to “CH1” via the following procedure.
C 390DD
While at “IR Channel” menu, use the [D/F] to go to “CH1” setting. Press
[S] or [ENTER] to select “CH1”. Press [A] to exit IR Channel selection.
AVR 4
Press and hold [AMP] in the DEVICE SELECTOR section of the AVR 4.
While holding down the device button [AMP], press “1”, “1” and “0” using
AVR 4’s numeric buttons.
Press [ENTER] while still holding down the device button [AMP]. The
AMP device selector will ash once to indicate that the library input is
successful.
With both C 390DD and AVR 4 set to “CH1”, the C 326BEE can now be
remotely controlled independent of the C 390DD.
NOTE
Performing a Factory Reset for C 390DD or AVR 4 will result to a return to
the factory default “IR Channel 0” setting.
AUTO STANDBY
The C 390DD can be setup to automatically go to standby mode if there is
no active input in the current source for 30 minutes.
Auto Standby
}~On
`Off
On: C 390DD will automatically go to standby modeif there is no active
input in the current source for 30 minutes.
O: C 390DD will remain at operating mode even if there is no active input
in the current source for 30 minutes.
SOURCE SETUP
Source Setup
}Digital Coaxial 1
Digital Coaxial 2
Digital Optical 1
Source Setup makes it possible to select a Source and enable or disable it as
desired. The optional NAD DD AP-1 (Direct Digital Analog Phono) module
must be installed for “Single-ended and “Balanced” sources to be functional.
The same applies for “Digital HDMI 1”, “Digital HDMI 2” and “Digital HDMI 3”
- the optional NAD DD HDM-1 (HDMI) module must also be installed. If the
applicable module is not installed, the corresponding sources will not be
available from the Source Setup menu selection.
OPERATION
USING THE C 390DD
19
ENGLISHFRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for NAD C 390 DD at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of NAD C 390 DD in the language / languages: English as an attachment in your email.

The manual is 2,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of NAD C 390 DD

NAD C 390 DD User Manual - German - 24 pages

NAD C 390 DD User Manual - Dutch - 24 pages

NAD C 390 DD User Manual - French - 24 pages

NAD C 390 DD User Manual - Italian - 24 pages

NAD C 390 DD User Manual - Swedish - 24 pages

NAD C 390 DD User Manual - Spanish - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info