667807

NAD C 388 Hybrid Digital DAC Amplifier Manual

16
Zoom out
Zoom in
Previous page
1/22
Next page
IR CHANNEL
The C 388 has the capability to operate via Alternate IR channel. This is
useful if you have two NAD products that can be operated by similar
remote control commands. With alternate IR Channel, two dierent NAD
products can be controlled independently in the same zone by setting
each one to a dierent IR channel.
IR Channel Assignment
The C 388 and the SR 9 remote control must be set to the same channel.
To change the IR Channel on the C 388
While at IR Channel menu, use the [a/s] to select through Channel 0 to
Channel 3. Press [ENTER] to select preferred IR Channel setting. C 388 IR
Channel is defaulted to Channel 0.
To change the IR Channel on the SR 9 remote control
• Include a channel number before the library code. For SR 9, library code
“10” is the default library table for “AMP” device. To select this “AMP”
library table for Channel 0, retain the library code “10” (or “010”).
• If you want to load the “AMP” library table on ”Channel 1” prex the
library code with “1” to indicate association with “Channel 1”. Load then
the “AMP” library table using the code “110”. Repeat the same for MP
(130) and TUNER (140).
SAMPLE SETUP OF TWO NAD PRODUCTS ON THE SAME ZONE
NAD C 388 and NAD C 390DD are both defaulted to Channel 0. If [OFF]
button is pressed on the SR 9 remote control (or AVR 4 remote control for
the C 390DD), both products will go to standby mode. Press [ON] and both
products will power up from standby mode.
To prevent both products from simultaneously going in and out of standby
mode along with other common commands, set each one to a dierent
IR channel. In this setup, we will keep C 390DD and AVR 4 remote control
defaulted to “Channel 0”. As for C 388, we will assign it to “Channel 1”; the
same applies to SR 9.
Set C 388 and SR 9 to “Channel 1” via the following procedure.
C 388
While at “IR Channel” menu, use the [a/s] to go to “Channel 1” setting. Press
[ENTER] to select “Channel 1”.
SR 9
• Press and hold [AMP] in the DEVICE SELECTOR section of the SR 9.
• While holding down the device button [AMP], press “1”, “1” and “0” using
SR 9’s numeric buttons.
• Press [ENTER] while still holding down the device button [AMP]. The
AMP device selector will ash once to indicate that the library input is
successful.
With both C 388 and SR 9 set to “Channel 1”, the C 388 can now be
remotely controlled independent of the C 390DD.
NOTE
Performing a Factory Reset for C 388 or SR 9 will restore their respective
IR channel setting to “Channel 0”.
IR LEARNING DEVICE
IR Learning Device enables any non-NAD remote control to learn AMP
and BluOS basic remote control codes. With the learned codes, use the
congured non-NAD remote control to command or operate the C 388.
HOW TO LEARN REMOTE CONTROL CODES
1 Go to IR Learning Device menu. Select either AMP or BLS.
2 Select AMP and the rst Amp Learning Key appears – VOLUME UP.
3 Press ENTER to select VOLUME UP and initiate learning mode.
4 Direct or point the non-NAD remote control to the IR sensor in the
front panel. Then, press desired button on the non-NAD remote
control where VOLUME UP will be learned. Upon pressing the
designated button, display will turn to “Learned”.
5 “VOLUME UP” is now learned into the designated button. Repeat
the same for the other codes to be learned. The same procedure
applies for BLS learning.
OPERATION
USING THE C 388
IR Channel
SettingsSource Setup
Channel 0
Settings
IR Learning Device
SettingsSource Setup
AMP
Settings
Amp Learning Key
SettingsSource Setup
VOLUME UP
Settings
VOLUME UP
SettingsSource Setup
Learning...
Settings
VOLUME UP
SettingsSource Setup
Learned
Settings
16
ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ
… 16 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for NAD C 388 Hybrid Digital DAC Amplifier at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of NAD C 388 Hybrid Digital DAC Amplifier in the language / languages: English as an attachment in your email.

The manual is 2,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of NAD C 388 Hybrid Digital DAC Amplifier

NAD C 388 Hybrid Digital DAC Amplifier User Manual - German - 20 pages

NAD C 388 Hybrid Digital DAC Amplifier User Manual - Dutch - 22 pages

NAD C 388 Hybrid Digital DAC Amplifier User Manual - French - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info