667804
13
Zoom out
Zoom in
Previous page
1/20
Next page
BASS, TREBLE, BALANCE
Bass and Treble controls only aect the low bass and high treble leaving
the critical midrange frequencies free of coloration.
Use [a/s] to boost or cut Bass or Treble levels within ±7 dB range.
Balance control adjusts the relative levels of the left and right speakers.
Press [s] to shift the balance to the right or [a] to shift the balance to
the left. Use [a/s] also to recover or even out the balance levels.
“0 dB” level setting provides equal level to the left and right channels.
FILTERS
Filters provide easy bi-amplication or subwoofer integration by adding the
required lters to redirect bass frequencies to the subwoofer.
High Pass: Low pass signal up to 300 Hz is attenuated and over 300 Hz
sent to the speakers.
Full Range: Refers to the whole frequency spectrum capability of your
C 368 and speaker system. This is ideally 20 Hz to 20 kHz.
PRE OUT/SUBWOOFER
Pre Out/Subwoofer feature allows you to select the function of the PRE-
OUT or SUBWOOFER terminals.
Pre Out: Congured as Pre Out terminals.
Subwoofer: Congured as Subwoofer terminals.
SPEAKER CHANNEL
SPEAKER CHANNEL enables you to engage or disengage the speakers
connected respectively to the SPEAKERS A and SPEAKERS B terminals on
the rear panel.
Select “Speaker A” or “Speaker B” individually and then set to “On or “O.
On: Selected speaker is enabled.
O: Selected speaker is disabled.
TEMPORARY DISPLAY
Temporary Display feature enables the display to be turned o temporarily
after 10 seconds of non-user interface.
On: Display is turned o temporarily after 10 seconds of non- user
interface. The Standby LED is also turned o at the same time. Display
and Standby LED are activated once user interface is initiated.
O: Display remains illuminated.
DIMMER
DIMMER function makes it possible to adjust the brightness level of the
front panel display.
Bright: Above normal level of display brightness.
Normal: Normal level of display brightness.
Dim: Below normal level or dimmer than normal display brightness.
NETWORK STANDBY
Network Standby mode maintains network connection at standby mode
with reduced system performance level.
On: Network connection is maintained at standby mode.
O: Network connection is disconnected at standby mode.
Refer also to table below about “OPERATING MODE TRIGGER POINTS”.
OPERATION
USING THE C 368
Balance
SettingsSource Setup
0 dB
+-
Settings
Filters
SettingsSource Setup
High Pass
Settings
Pre Out/Subwoofer
SettingsSource Setup
Pre Out
Settings
Speaker Channel
SettingsSource Setup
Speaker A
Settings
Bass
SettingsSource Setup
0 dB
+-
Settings
Treble
SettingsSource Setup
0 dB
+-
Settings
Dimmer
SettingsSource Setup
Bright
Settings
Temporary Display
SettingsSource Setup
Off
Settings
Network Standby
SettingsSource Setup
Off
Settings
13
ENGLISHFRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for NAD C 368 - Hybrid Digital DAC Amplifier at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of NAD C 368 - Hybrid Digital DAC Amplifier in the language / languages: English as an attachment in your email.

The manual is 2,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of NAD C 368 - Hybrid Digital DAC Amplifier

NAD C 368 - Hybrid Digital DAC Amplifier User Manual - German - 20 pages

NAD C 368 - Hybrid Digital DAC Amplifier User Manual - Dutch - 22 pages

NAD C 368 - Hybrid Digital DAC Amplifier User Manual - French - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info