667804
7
Zoom out
Zoom in
Previous page
1/20
Next page
6 BRIDGE MODE
The C 368 amplier can be congured to be MONO (Bridge Mode),
more than doubling its output power. This way, the C 368 can be used
as part of a high power stereo or home-theatre system, by connecting
additional power ampliers.
In BRIDGED MODE (switch at ON (MONO) setting), the C 368 will
produce approximately 160W into an 8 ohm loudspeaker. In this
mode, the amplier sections will react as though the speaker
impedance has been halved. Low impedance speakers (under 8
ohms) are not recommended when using Bridge Mode as these
may cause the ampliers thermal cut-out to operate if played at
high levels.
Set the BRIDGE MODE switch to the “ON (MONO)” position and
connect the speaker to the terminals marked “L +” and “R-” ensuring
that the “L+” is connected to the “+” terminal of your speaker and
the “R-” is connected to the speakers “ - ” terminal.
7 SPEAKERS
The C 368 has two sets of SPEAKER connections which are identical
in function (parallel connection).
Connect C 368’s Right speaker terminals marked “R +” and “R-” to
the corresponding “+” and “-“ terminals of your designated right
speaker. Repeat the same for C 368’s Left speaker terminals and
corresponding left speaker.
Double check the speaker connections before powering up the
C 368.
IMPORTANT NOTES
The blue terminals must never be connected to ground (earth).
Never connect the blue terminals together or to any common ground
device.
Do not connect the output of this amplier to any headphone adapter,
speaker switch or any device that uses common ground for left and
right channels.
NOTES
Use 16 gauge (American Wire Gauge or AWG) or lower stranded wire.
Connections to the C 368 can be made with banana-type plugs.
Bare wire or pins can also be used by loosening the terminal’s plastic
nut, making a clean, neat connection and re-tightening. To minimize
the danger of a short circuit, ensure that only 1/2-inch of exposed wire
or pin is used to connect and no loose strands of speaker wire.
8 POWER
Supplies the AC mains power to the C 368.
When the POWER switch is set to ON position, the C 368 goes to
standby mode as shown by the amber status condition of the front
panel Power indicator.
Press the front panel Standby button or SR 9’s remote control’s [ON]
button to switch ON the C 368 from standby mode.
If you do not intend to use the C 368 for long periods of time (such
as when on vacation), switch o the POWER switch.
With POWER switched o, neither the front panel Standby button
nor SR 9 remote control’s [ON] button can activate the C 368.
9 FUSE HOLDER
Only qualied NAD service technicians can have access to this fuse
holder. Opening this fuse holder may cause damage thus voiding
the warranty of your C 368.
10 AC MAINS INPUT
The C 368 comes supplied with two separate mains power cords.
Select the mains power cord appropriate for your region.
Before connecting the plug to the mains power source, ensure that
it is rmly connected to the C 368’s AC Mains input socket.
Always disconnect the mains power plug from the mains power
source before disconnecting the cable from the C 368’s AC Mains
input socket.
11 SERVICE
Use for servicing purposes only. Not for consumer use.
12 BLUETOOTH ANTENNA TERMINAL
Install supplied Bluetooth antenna to this Bluetooth antenna
terminal.
13 GROUND TERMINAL
Ensure that the C 368 is plugged-in to a grounded AC wall outlet.
If necessary, use this ground terminal to connect to ground a
phono or turntable source for PHONO input.
If a separate earth ground is necessary, use this terminal to ground
your C 368. The C 368 can be connected to ground by connecting
a ground lead wire or similar to this terminal. After insertion, tighten
the terminal to secure the lead.
EXAMPLE ILLUSTRATION OF GROUNDING THE C 368 VIA THE
REAR PANEL GROUND TERMINAL
14 RS 232
NAD is a certied partner of AMX and Crestron and fully supports
these external devices. Check out the NAD website for information
about AMX and Crestron compatibility with NAD. See your NAD audio
specialist for more information.
Connect this interface using RS-232 serial cable (not supplied) to
any Windows compatible PC to allow remote control of the C 368
via compatible external controllers.
Refer to the NAD website for information about RS232 Protocol
documents and PC interface program.
IDENTIFICATION OF CONTROLS
REAR PANEL
7
ENGLISHFRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for NAD C 368 - Hybrid Digital DAC Amplifier at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of NAD C 368 - Hybrid Digital DAC Amplifier in the language / languages: English as an attachment in your email.

The manual is 2,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of NAD C 368 - Hybrid Digital DAC Amplifier

NAD C 368 - Hybrid Digital DAC Amplifier User Manual - German - 20 pages

NAD C 368 - Hybrid Digital DAC Amplifier User Manual - Dutch - 22 pages

NAD C 368 - Hybrid Digital DAC Amplifier User Manual - French - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info