493507
12
Zoom out
Zoom in
Previous page
1/16
Next page
USING THE SR 8 REMOTE CONTROL LIBRARY
The SR 8 can store a dierent library of default NAD codes for each
of its DEVICE SELECTOR “pages. If the original default library does not
control your NAD CD player, DVD player or other components, follow the
procedure below to change the library code. Refer as well to the table
below for a list of applicable NAD Library Codes with their corresponding
NAD models.
LOAD ANOTHER LIBRARY CODE
Example: Load NAD DVD Player T 517 library codes to SR 8’s “CD device.
1 Press and hold [CD] in the DEVICE SELECTOR section of SR 8.
2 While holding down the device button (CD), press “2” and “2” using SR
8’s numeric buttons. “22” is the corresponding library code for T 517.
3 Press [ENTER] while still holding down the device button (CD). The
CD device selector will ash once to indicate that the library input is
successful. Both the device selector button (CD) and [ENTER] can now
be released.
RESET THE SR 8 TO ITS DEFAULT SETTINGS
The SR 8 can be restored to its factory settings, including default libraries,
by the following procedures
1 Press and hold [ON] and [DELETE/CLEAR] buttons for about 10 seconds
until the AMP device button lights up.
2 Within two seconds of the AMP device button lighting up, release both
buttons. If the reset mode is successful, the [CD] device button will ash
twice.
TABLE OF LIBRARY CODES APPLICABLE TO SR 8 REMOTE
CONTROL
LIBRARY
CODE
NAD PRODUCT DESCRIPTION
10 Default library for AMP page
11 Zone 2
20 Default library for “CD” page; C 515BEE, C 545BEE, C565BEE
21 T 535, T 585, M55, DVD section of L 54, VISO TWO, VISO FIVE
22 T 513, T 514, T 515, T 517
23 T 587
31 IPD 2
40
Default library for “TUN” page; Tuner section of C 725BEE, T 175,
T737, T 747, T 755, T 765, T775, T 785
41 C 422, C 425
42 C 445
NOTE
The SR 8 may not necessarily contain all the control buttons applicable
for the above-mentioned NAD products. Use the prescribed remote
control of the specic NAD product for a full compliment of the
applicable remote control buttons.
ALTERNATE IR CHANNEL
The C 326BEE has the capability to operate via Alternate IR channel. This
is practically useful if you have two NAD products that can be operated by
similar remote control commands. With alternate IR Channel, two dierent
NAD products can be controlled independently in the same zone by
setting each one to a dierent IR channel.
IR CHANNEL ASSIGNMENT
The C 326BEE and the SR 8 remote control must be set to the same
channel.
To change the IR Channel on the C 326BEE
Press and hold [MP] button and then press Standby button. Observe the
number of times the Standby LED ashes.
• IR Channel 1 - Standby LED ashes once.
• IR Channel 2 - Standby LED ashes twice.
To change the IR Channel on the SR 8 remote control
• Include a channel number before the library code. For SR 8, library code
“10” is the default library table for AMP device. To select this AMP”
library table for “IR Channel 0”, retain the library code “10”.
• If you want to load the AMP” library table on “IR Channel 1”, prex the
library code with “1” to indicate association with “IR Channel 1”. Load
then the AMP library table using the code “110”.
SAMPLE SETUP OF TWO NAD PRODUCTS ON THE SAME ZONE
C 326BEE and T 787 are both defaulted to IR Channel 0. If [OFF] button is
pressed on the SR 8 remote control (or HTR 8 remote control for the T 787),
both products will go to standby mode. Press [ON] and both products will
power up from standby mode.
To prevent both products from simultaneously going in and out of standby
mode along with other common commands, set each one to a dierent
IR channel. In this setup, we will keep T 787 and HTR 8 remote control
defaulted to “IR Channel 0”. As for C 326BEE, we will assign it to “IR Channel
1”; the same applies to SR 8.
Set C 326BEE and SR 8 to “IR Channel 1” via the following procedure.
C 326BEE
• Press and hold [MP] button and then toggle STANDBY button until the
Standby LED ashes twice - C 326BEE is set to “IR Channel 1”.
SR 8
Begin by ensuring that the C 326BEE is powered-up (“on, not merely in
standby).
• Press and hold [AMP] in the DEVICE SELECTOR section of the SR 8.
• While holding down the device button [AMP], press “1”, “1” and “0” using
SR 8’s numeric buttons.
• Press [ENTER] while still holding down the device button [AMP]. The
AMP device selector will ash once to indicate that the library input is
successful.
With both C 326BEE and SR 8 set to “IR Channel 1”, the C 326BEE can now
be remotely controlled independent of the T 787.
NOTE
Performing a Factory Reset for SR 8 will result to a return to the factory
default “IR Channel 0” setting.
IDENTIFICATION OF CONTROLS
SR 8 REMOTE CONTROL
12
ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for NAD C 326 BEE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of NAD C 326 BEE in the language / languages: English as an attachment in your email.

The manual is 1,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of NAD C 326 BEE

NAD C 326 BEE User Manual - German - 16 pages

NAD C 326 BEE User Manual - Dutch - 16 pages

NAD C 326 BEE User Manual - French - 16 pages

NAD C 326 BEE User Manual - Italian - 16 pages

NAD C 326 BEE User Manual - Swedish - 16 pages

NAD C 326 BEE User Manual - Spanish - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info