493502
7
Zoom out
Zoom in
Previous page
1/12
Next page
1 INPUT SELECT: Slide this switch to either “FIX” or VAR”. When it is
set to FIX, the input signal is taken straight to the power amplier’s
circuitry. This setting is normally used in a system with only one power
amplier or multiple but identical power ampliers.
When the INPUT SELECT switch is set to VAR” (Variable), it is possible
to adjust the volume level for both channels simultaneously, using the
INPUT LEVEL CONTROL. This can be useful for:
Level Matching
In a surround sound or system with more than one set of speakers,
dierences in levels can occur due to variance ineciencies between
these speakers. In case your preamplier or processor also has
individual trims for each channel, set these to neutral or mid position
(usually marked as 0dB). Adjust the INPUT LEVEL CONTROL so that
the speakers driven by the C 275BEE have the correct volume level
compared to the other speakers, judging from your listening position.
Extended Volume Control Range
Many systems have so much voltage gain that the speakers (or your
ears) are overdriven at any volume control setting higher than 11 or 12
oclock. As a result you are conned to using only the lower half of the
volume control’s range, where adjustments are imprecise and where
channel balance errors tend to be greater.
If the input level is reduced, you can turn up the volume control of
your processor or preamplier, making more eective use of its range.
(Suggestion: adjust the input level controls so that your preferred
maximum sound levels usually occur at about 2 or 3 oclock on the
volume control.) As an added benet, this procedure suppresses any noise
produced by the preamplier’s high level circuitry (e.g. any residual hum or
hiss that does not go away when the Volume is turned down).
Bi-Amping
Some loudspeakers have separate connection terminals for their LF
(Low Frequency) and HF (High Frequency) sections. Where a separate
power amplier is used for the LF and HF section, this facility allows to
“Bi-Amp such speakers which may improve overall sound quality. When
Bi-Amping with dierent models of power ampliers, it is likely to occur
that one power amplier has more gain” than the other, resulting in a
mismatch in level for the woofer and tweeter of the speaker. Adjust the
level control so that woofer and tweeter are in perfect balance with
each other (identical gain of power ampliers).
NOTES
· Always turn OFF the C 275BEE and other components in the system before
connecting or disconnecting anything to the INPUT sockets.
· When the INPUT SELECT switch is set to “VAR” for the rst time, it is
advised that the “INPUT LEVEL CONTROL” level of the C 275BEE or the
volume control level of your preamplier/processor be set to their
minimum settings. This prevents inadvertently beginning a session at
excessive volume. You can then adjust both controls to your desired
listening level.
2 INPUT: Connect the output from a pre-amplier or processor, such as
a surround-sound decoder, to this set of inputs. Use a twin RCA-to-RCA
lead to connect the left and right Audio Output of the preamplier or
processor to these input sockets.
3 INPUT LEVEL CONTROL: The INPUT LEVEL CONTROL works in
combination with the VAR” (Variable) input setting. Turn clockwise to
increase the VAR (Variable) volume level; counter clockwise to lower it.
IDENTIFICATION OF CONTROLS
REAR PANEL
1 2 3 4 5 6 7
9 10 11
ATTENTION!
Please make sure that the C 275BEE is powered OFF or unplugged before making any connections. It is also advisable to power-down or unplug all
associated components while making or breaking any signal or AC power connections.
8
7
ENGLISHFRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for NAD C 275 BEE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of NAD C 275 BEE in the language / languages: English as an attachment in your email.

The manual is 0,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of NAD C 275 BEE

NAD C 275 BEE User Manual - German - 12 pages

NAD C 275 BEE User Manual - Dutch - 12 pages

NAD C 275 BEE User Manual - French - 12 pages

NAD C 275 BEE User Manual - Italian - 12 pages

NAD C 275 BEE User Manual - Swedish - 12 pages

NAD C 275 BEE User Manual - Spanish - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info