30282

Multiplex ROYALevo9 Manual

9
Zoom out
Zoom in
Previous page
1/58
Next page
Instructions
Seite 9
ENGLISH
Fig. 4
7.4.2. Adjusting the transmitter aerial,
fitting a new aerial
The transmitter aerial is a permanent fitting in the case.
For transport it can be collapsed completely and re-
cessed into the case. For adjustments and programming
the aerial can be left in this position without damaging
the RF section.
!
When operating a model always extend the
aerial to its full length. Only in this configura-
tion can you be sure of safe operation with
maximum radiated power and range.
The aerial can also be moved to a second position (an-
gled up and to the left), and locked in that position:
1. Pull out the aerial until you feel a distinct resistance
(Fig. 1).
2. Pull the aerial another 3 to 5 mm to overcome the
resistance, pulling fairly hard, and swivel the aerial
up and to the left (Fig. 2). You will again feel resis-
tance at this point, but this time do not push past it.
3. Tilt the aerial as far as it will go, and it will latch in
the correct position..
To swivel it back, the aerial must first be unlocked again
as described under point 2.
!
Check regularly that the aerial is still making
good contact. Contact problems with telescopic
aerials cause adverse effects on radiated power,
and thereby reduce effective range. In such
situations reliable operation can no longer be
guaranteed. Intermittent contact or bent aeri-
als should be replaced at the earliest opportu-
nity, as should an aerial that has become loose
and sloppy through hard use.
If the aerial should be damaged, it can be replaced eas-
ily as follows: Remove the case back, and simply push it
back and out of the aerial guide sleeve (replacement
ROYALevo aerial: # 89 3002).
Fig.1:
Fig. 2:
7.4.3. Installing and removing the RF module
The two RF modules (HFM-4 and HFM-S) for the ROYA-
Levo are not fitted in protective cases. To avoid dama-
ging them:
x Don’t touch the circuit board and its components.
x Don’t exert any force on the circuit board.
x Protect RF modules from mechanical strain.
!
Don’t touch components on the circuit board.
Don’t change the settings of adjustable com-
ponents.
If settings have been changed mistakenly or com-
ponents are damaged, have the module checked
an realigned by the MULTIPLEX service.
Removing the RF module:
1. Switch off the transmitter!
2. Open the transmitter (Î 7.4.1.)
3. Lay the front face of the transmitter on a soft sur-
face, taking care to avoid damage to the sticks and
switches!
4. Grasp the RF module by all four corners using both
thumbs and index fingers, and carefully pull it up
and out (see picture below).
Replacing the RF module:
Grasp the RF module as before. Ensure that the module
is fitted onto the contact pins correctly, i.e. that it is not
offset in any direction.
!
When changing the RF module avoid touching
the electrical components at all costs. If the
module is to be stored outside the transmitter,
it is essential to protect it from dirt and damp,
and also from shock and vibration.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Multiplex ROYALevo9 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Multiplex ROYALevo9 in the language / languages: English as an attachment in your email.

The manual is 3,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Multiplex ROYALevo9

Multiplex ROYALevo9 User Manual - German - 58 pages

Multiplex ROYALevo9 User Manual - Dutch - 110 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info