30252
69
Zoom out
Zoom in
Previous page
1/79
Next page
Please note this difference
between
the
transmitter
controls
and
the other switches,
as
described
above,
It is
quite
difficult to describe
these
checks, but
you
will
find that they only
take a
moment to carry out!
Fig.50
Fig.51
Accessories
Stick
tops
The transmitter
is supplied
with 3
pairs
of stick
tops:
short,
medium-length,
and
long.
Each one
can be adjusted
in
length by about
10mm.
Select
the
length which suits
your preference.
To
adjust
or change
the stick
top, rotate the
grip
until
you
teel
it
"unlatch",
then
adjust the
length or
pull
it
off
altogether.
Slip
the new
grip
into
place,
set
it to the
required
length, then turn
it through about
180 degrees
(Fig.
52).
Stick
press-button
The long and
medium-length
stick tops
can be fitted
with a
press-button (momentary
contact),
as shown
in
Fig.
53. This can
then be used
either as a
"transmitler
control"
or as
a reversing or
coupling switch.
Using
the
press-button:
As a
transmitter control:
actuating
a tow'release
mechanism
As change-over/coupling
switch: operating
the stopwatch
Stick
switch
It is also
possible
to tit an ON/OFF
switch
to the stick
rop.
The advantage
of this
form of switch
is that
you
can
see
and
teel the current
position
of
the switch at
any
time.
Applications:
Fixed
wing: flap switch
tow
release
Helicopter:
auto-rotation
switch
The
press-button
and
switch can
only be
installed by
the
MULTIPLEX Service
Department.
Please contact
us
if
you
want the
job
done;
addresses
are
in the
aooendrx.
Relocating or
installing switches
The switches
and their
location on
the standard
transmitter
have been chosen
carefully
to meet most
modellers'
practical
requirements.
However,
you
are
free to move
the
switches
to suit
your
own
preference.
The transmitter
is supplied
with two
blank
switch
panels
and
legend sheets
to help
you.
Additional
switches are available
in
several
versions.
lf
you
wrsh to rearrange
the
layout of
your
transmittet
please
bear in
mind the following
points:
The Digi-Adjustor can
only be
titted in switch bays
1, 2,
5 and
6
(see
page
5); its
mounting bracket obstructs
one adjacent switch
bay.
lf
you
have switches
with a short
toggle
installed, other
switches
with a
long toggle should only
be fitted in
the
row
furthest from
you.
lf
you
want to change
the switch
layout
you
must first
remove
the existing
switches; undo
the
knurled nuts
using
the special spanner
supplied
with the set.
lf
you
want to re-locate
the Digi-Adjustor,
undo
the
grubscrew
and
remove
the rotary
knob.
With the switches
removed,
you
can
press
the existing
switch
panel
out of the
transmitter
from the inside,
by
squeezing
its central
snap fixing and
pushing
it out.
ll
you
wish to change
the
position
of the
Digi-Adjustor,
you
must remove
the switch
panel
first.
Please note
that
the washer on
the fixing screw
is not symmetlical,
as
the spacing
of the switch
bays
in the right/left
direction
is different
lrom the
fore/aft direction.
Turn the
washer
as necessary,
and check
that the shaft
of the
Adjustor is central
in
its hole. The
fixing screw can
be
re-tightened
when this
is the case.
It is best
to cut out
the holes
you
need in the
new
switch
panel
before
you
install
it in the transmitter.
As
the
plastic
is much
thinner at the
hole
positions,
this
can
easily be
done with a sharp,
pointed-blade
modelling
knife.
Caution:
the switch
panels
only fit one
way round
-
take care
not to cut
out the
wrong holes!
lf necessary,
the MULTIPLEX Service
Department
will help
you
out
with
a
new
panel.
Install the switch(es).
Before tightening
the fixing
nut
permanently
and deploying
the connecting
leads, run
through
the
"Transmitter
Control
Test"
(see
page
66),
to ensure
that the switches
are installed
the right
way
round.
You will
find more details
about switches
on
page
7
("Connectors
on the
main electronics
circuit
board")
and
page
12
("Transmitter
controls and
switches").
Fig.53
r-rg.52
ot
69


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Multiplex PROFImc3010 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Multiplex PROFImc3010 in the language / languages: English as an attachment in your email.

The manual is 5,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Multiplex PROFImc3010

Multiplex PROFImc3010 User Manual - German - 78 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info