Manual Multiplex PROFImc3010 (page 10 of 79) (English)

30252

Zoom out

Zoom in

1/79

Fig. 18

You can use the earlier

version of the MULTIPLEX Com-

bi-Charger,

Order

No. 14

5540,

to slow-charge the bat-

tery

In this case select the

100 mA

charge

current and

charge

for at least 24

hours. At

this

current

you

can

leave the transmitter connected

to the charger con-

stantly;

it is not

possible

to damage the battery or

the

transmitter

at such a low current.

Be sure

to switch the transmitter off beJore

recharging.

Then connect the transmitter

(charge

socket) to

the

charger

using the charge

lead supplied.

Red

plug

(positive)

socket on the charger,

blue

plug

(negative)

socket.

Rapid charging

The transmitter can be

rapid-charged

only

1to 2

hours. However,

this salely

you

must use the

MULTIPLEX

Automatic

Rapid

Charger,

Order

No.

2505.

you

use a ditferent

rapid charger, or a difterent

charg-

ing

process,

there

is a

danger

of damaging

the battery

and the transmitter.

We would

not

be able

to repair the

unit under

guarantee

under such circumstances.

you possess

a charger

which is not compatible

with

the

protective

circuitry

your

new transmitter,

please

contact our Customer Service

deDartment.

For rapid-charging select an output

current ol 1

2 A.

Provided that

you

are using the

recommended charger,

you

do not need to concern

yourself

with the battery's

initial state of charge.

the

2 A rate, and

with

a com-

pletely

discharged battery

the charge

period

is about

3/4

hour; in any case the charger

switches itsel{ off

when the battery

is fully

charged.

Caution: the charge

rate must

not

exceed

2 A. At

higher

currents

the transmitter

fuse will

burn out.

Do not be tempted

to install a

higher rated fuse, as

you

risk

damaging

the transmitter.

you

damage

the trans-

mitter by exceeding

the recommended

charge

current, we

will

be unable

to repair

it under

guarantee.

Note:

brand

new battery cannot exploit

its full capacity

right

from

the

outset. In fact, it only achieves

full capacity

after a few charge/discharge

cycles

10). Please bear

this in

mind when

you

start using the equipment,

as the

full

operating

period

will not be available

first.

you

need

full

battery

capacity at once,

we recommend

that

you

charge

the ilansmitter,

leave it switched

on un-

til the

battery is completely

discharged, then

recharge

it fully. Repeat thrs cycle

several times.

The

keypad aN

the

qy$tgfi

The tirst

part

of this Section explains

how the

keypad is

useo.

After this

you

will find a brief

introduction to

how the

"device

guides

the user" through

menus.

The

Section

concluded

with a brief

explanation

of the

transmitter's

menu structure.

The

keypad

Fig. 19

These

eight

keys, used

in conjunction

with the

LCD

screen,

give you

complete

access

to all the selection

and adiustment

tunctions.

The keys are

in three

groups,

and

it is easy to

remember

what they do.

Very

briefly,

the keys

have the following

functions:

The

key

This is the

"Menu"

key. You use

it first

move from the

display

into the

"Menu

tree". Within the

tree

the

key

always used

to conclude

any

proce-

dure,

and to move back

into the

preceding

menu.

Re-

gardless

of where

you

are

in the

menu tree,

you

can

re-

turn

to the Status display

at any time

pressing

this

key one or

more times.

The

key

R stands

for Reverse

that's all

there

to say.

This

key

used

to reverse a servo,

or switch something

off

or on. More on

this in the explanation

of the individual

menus.

The

and

keys

These

keys are also

more or less sellexplanatory

something

is to be

increased or

reduced, then

you

with these two

keys. You can also

use them to

"leaf

through"

lists of options at

many

places

in the various

menus.

Examples

of using the

and

keys:

Adjusting servo

travel

Adjusting a

mixer input value

Switching

to a different

memory

Moving on to the

next transmitter control

when

testing etc.

One

special

teature here: where

it is of

practical

use,

these

keys Jeature an auto-repeat

function.

you

press

the

key briefly,

its

action

occurs once.

you

hold

pressed

down, the action

is repeated automatically.

You

simply

need to

press

the key and

watch the display,

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Multiplex PROFImc3010 in the language / languages: English as an attachment in your email.

The manual is 5,25 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Multiplex PROFImc3010

Multiplex PROFImc3010 User Manual - German - 78 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Multiplex PROFImc3010 Manual

Product: