BA TS3x10knx Hardware HM;DE,GB -23773- 2017.11V02 ED.doc
INSTRUCTION MANUAL AIR QUALITY SENSORS TS3X.10KNX
HUGO MÜLLER GMBH & CO KG, STURMBÜHLSTR. 145-149, 78054 VS-SC
HWENNINGEN
SAFETY INSTRUCTIONS AND BASICS
TS30.10knx
TS 31.10 knx
Technical data
Safety instructions / Intended use
Power supply:
Bus current:
Via KNXbus voltage
< 10 mA
CAUTION!DANGER OF FIRE AND ELECTRIC SHOCK!
!!!Installation and assembly of electrical equipment must be carried out only by a skilled person!!!
Bus system:
KNX
Connect only to suitable supply voltage [KNX bus voltage (nominal voltage 29V)].
Warranty void if housing opened by unauthorized person!
The electronic circuit is protected against a wide range of external influences. Incorrect operating may occur if external influences
exceed certain limits!
Installation and assembly of electrical equipment must be in accordance with national building, electrical and safety codes!
Defective devices / sensors have to be put out of service immediately!
Observe the regulations and instructions in the ZVEI/ZVEH handbook (building system technology). Especially the professional
installation of the bus lines and the professional installation and start-up of KNX devices must be observed!
The device fits for the particular use of the following tasks: monitoring of the air quality in building systems technology (schools,
offices, hotels, conference venue etc.), data transfer and regulation via bus system.
The device is intended for use in accordance with the defined technical data.
Operate the device exclusively in a dry room!
The device is not qualified for security relevant tasks such as emergency doors, fire protection equipment, fermenting cellars etc.
Sensors:
Temperature
Manual operation (TS 31.10 knx):
Manual adjustment of set-point temperature
±3° (increment 0.5°)
Measuring range relative humidity:
0–100%
Measuring range temperature:
0–50°C
Measuring range atmospheric pressure:
absolute atmospheric pressure
Permitted ambient temperature:
-0°…+50°C
Housing:
self-extinguishing thermoplastic
Mounting:
Wall
Type of connection:
Push-in connector
Type of protection:
IP 20 to DIN EN 60529
Class of protection:
III when installed according to regulations
Source of interference
Inappropriate use / disposal
Operation of TS 31.10 knx
The measurement results of the device can
be negatively i
nfluenced by external factors.
Possible sources of interference are:
■ Draught and air movement: e.g. through
windows, doors, convection, heating and
people
■ Warming and cooling: e.g. sunlight or
mounting on an outside wall
■ Heat sources: close to installed electrical
consumers e.g. dimmers
■ Vibrations or shocks, which the unites are
or were subjected to
■ Pollution due to colors, wallpaper paste,
dust e.g. at renovation work
■ Organic solvents or their vapours: e.g.
detergents
■ Plasticizers from stickers and packaging:
e.g. bubble wrap or polystyrene
The device is not intended for use of unauthorized constructional
alterations, repairs and security relevant tasks
The device is not intended for use in outdoor areas and wet rooms
The device is not qualified for security relevant tasks The controlling of
the deviceis only for the observation and regulation of the air quality
The inappropriate use of the device can cause damage to property and
persons
The device has to be disposed in an environmentally friendly manner
according to the current electrical codes!
Set-point temperature
manually adjustable
via touch-area
(adjustment range
±3°; increment 0.5°).
Display with LEDs.
ASSEMBLY
Assembly
Disconnect device from power supply for wiring and installation
purposes! Check power supply is disconnected!
Attention! You have to check and consider the safety instructions above!
This device is suitablefor wall mounting or for mounting on a flush-mounting box.
The device should not be exposed to dusty environment.
Ensure that no dust gets inside of the device.
Afterinitial startup, thedevice requiresup to 5 minutesuntil the firstcorrect
measurement is possible
STEP 1:Open the device with a small screw driver by pushing in the
lever at the bottom of the housing and gently remove the front cover.
STEP 2:Fix the rear cover, either directly to the wall or on a flush-mounting box
(see installation notes)
STEP 3:After wiring, press the “learn button” to set the device into programming
mode(this can be done at alater timeas well)
STEP 4:After completing the installation, the front cover must be reattached
Installation note:Make sure that no wires are pinched or squeezed when installing the cover.The mounting of the device on a flush-mounting box is recommended for easier handlingand wiring.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Muller TS 31.10 knx at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Muller TS 31.10 knx in the language / languages: English, German as an attachment in your email.
The manual is 0,72 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
