BA SC9840knx HARDWARE N; DE, GB - 23245 – 2013-05-V02 ED
Instruction Manual(Site 1/2)
GB
KNX time switch
Connection diagram
Directory
1. Safety instructions
!
!!ATTENTION!!DANGER OF LIFE / RISK OF FIRE AND ELECTRIC SHOCK!!
=> Installation and assembly of electrical equipment must be carried out only by professional electrician!
=> Disconnect device from power supply for wiring and installation purposes!
=> Defective devices have to be put out of service immediately!!!
!
Connect only to suitable supply voltage[KNX bus voltage (nominal voltage 29V)].
!
Warranty void if housing opened by unauthorised person!
!
The electronic circuit is protected against a wide range of external influences. Incorrect operating may occur if external influences exceed certain limits!
!
Installation and assembly of electrical equipment must be in accordance with national building, electrical and safety codes!
!
Observe the regulations and instructions in the ZVEI/ZVEH handbook (building system technology). Especially the professional installation of the bus lines and
the professional installation and start-up of KNX devices must be observed!
2. Initial operation
3. DCF / GPS/ BUS-time
The time switch is delivered in sleep-mode, the display is switched off.
Press -button for 1 second.
The current date and time is already programmed and European
daylight savings time is activated.
Select the desired language by pressing-
buttons and confirm it by
pressing . (Remark: By pressing you move one step backwards
from the current position)
If required, date, time and daylight savings time mode can be adjusted
also by pressing -buttons and a subsequent confirmation with .
DCF / GPS: The time switch can process a timesignal.The antenna is not included in
delivery of the time switch.
Disconnect power supply voltage
Connect the antenna as indicated by the connection diagram
Connect supply voltage
To use the BUS-time as standard for the time switch:
Please set as follows (please also check the manual of the application software):
Adjustments=> Summertime=> Disabled S/W Time
Options => DCF => GMT Offset 00h
4. Menu overview
5. Symbol legend
Channel is switched ON
Channel is switched OFF
For the current date the “holiday program” / “permanent by date” is activated
Standard programming step
Current state is based on a manual over-ride. The state will be cancelled with the next
programming step
Current state is based on a manual over
-ride. The state is permanent until terminated manually
Days of the week Monday, Tuesday, ... Sunday;
The underscores indicate if the program is active for the days above
I
Current state is based on a switching time with pulse function
Z
Current state is based on a switching time with cycle function
W
Weekday function: Switching time is entered by date but is shifted for future years in respect of
the weekday (E.g. Tuesdaythis year...Tuesdaynext year).
Element within sub-menu “program delete”
6. Key function
X
1x-Function active: The switching time will be executed only once.
1. To access the Enter-mode (program, adjustments, options) from the automatic-mode.
2. To revert to the beginning of the current (sub-) menu.
F
Switching function / switching time with Easter function: The switching function takes into account
the yearly shift of Easter holiday for future years and changes the date of the switching program
accordingly.
1. To adjust the flashing digit.
2. To scroll through a choice
D
DCF: The time switch receives the signal for the DCF -77 time standard
1. Automatic-mode: To switch the channel ON or OFF until the next programming step occurs.
2. Automatic-mode:A push longer than 3 sec. = Permanent switching status (7).
The time switch is locked; to unlock the device the PIN has to be entered
1. To activate the time switch when operated without power supply.
2. To confirm the selection or the entered data.
7. Handling advice
8. Channel ON OFF/ Permanent P
9. Programming menu
The time switch is programmable without external power supply
after pressing the -button.
To revert one step or one level back while in the Enter-
Mode press
.
After completion of a (sub-) menu confirming endwill return the
device into the automatic-mode.
With the choice changes from endto continue. By
confirming
continue
the time switch returns to the beginning of
the current (sub-) menu.
When confirming endbefore completion, the time switch returns
to the automatic-mode without saving the entered data.
Channel ON OFF
By pushing -buttons a manual switch of the channels
take place. The resulting switching status is marked with
the hand-symbol and remains until the next programming
step occurs. (temporary over-ride)
Permanent switching status
P
By pressing the corresponding channel button for
more than 3 sec. the channel is permanently switched ON
or OFF. The status remains until the next manual switching
occurs (> 3 sec.).(permanent over-ride)
10. Standard weekly program
11. Example for the programming of STANDARDswitching times (ONand OFF)
**The cycle function will only be available if it is activated (point 13)
A.If you want to program a standard weekly switching time (
on
,
off
) confirm
Standard
with .
B.For regular switching times choose
onor offwith -buttons and confirm with .
C.Within this level you activate the days of the week (1…7) on which the switching time should happen.
With
you activate “yes” or deactivate “no” the corresponding date. Confirm each day with .
D.Adjustment of the time: Hours
and.Minutes and.
E.Verify the entered switching time: If the flashing summary of the programming step is correct, verify
on
or
offwith . After verification you have the choice between edit/deleteand endwith .
F.If you want to proceed with programming, confirm
next switchingwith .
To leave the programming menu confirm
end.
Information: You can easily transfer switching times from one channel to the other if you use the
copy function.
12. Cycle
13. Cycle options
Standard weekly program:
Program ->newprogram ->channelA/B/C/D ->Standard -> …
Special (weekly) program (to be activated by date for the yearly function):
Program ->newprogram ->channelA/B/C/D ->Special-program -> SP-entry-> program-number -> …
For the cycle function it is possibile to enter a periodic switching time. The time switch acts as a recycling timer and
switches between pulse (ON) and pause (OFF). The max. value for pulse and pauseis 9:59:59h:mm:ss.
If you haven’t defined and activated a cycle, the cycle function will not be available as switching time. Therefore you
have to activate and define at least one of the four cycles within menu Optionsand sub-menu Cycle(point 13).
Thecycle switching time will be terminated by another switching time (on, off, pulse
) or by another cycle switching
time.
Options ->Cycle ->Cycle 1 - 4 ->…
You have the possibility to define 4 different Cycles. For these purposes choose menu Optionsand sub-menu Cycle. The different
cycles can be activated, defined or deactivated (the max. value for pulse or pause is 9:59:59h:mm:ss):
Choose menu Optionsand sub-menu Cycleand confirm with .
Select with -buttons one out of the 4 cycles (Cycle 1 – Cycle 4) and confirm with .
Activate the cycle by changing Noto Yeswith -buttons and subsequent confirming with .
Define duration of the pulse „on-time“ ( -> …).
Define duration of the pause „off time“ ( -> …).
Confirm Endwith .
The cycle is now offered within the programming menu.
Further applications of the cycle function in combination with: External Input function and/or Channel keys function.
14. Pulse
15. Priorities of the switching programs
Standard weekly program:
Program ->newprogram->channelA/B/C/D ->Standard -> …
Special (weekly) program (to be activated by date for the yearly function):
Program ->newprogram->channelA/B/C/D ->Special-program -> SP-entry-> program-number -> …
The pulse function provides you the opportunity of programming a switching time with a defined duration.
As soon as the pulse-
duration has expired the time switch switches OFF automatically (the duration of the pulse is up to
59:59 mm:ss).
Standard switching times, Special programs, Extra switching times and Permanent by date are executed according to their
corresponding priority (by channel and date)
All switching programs exceptExtra switching times, suspend all other switching programs with lower priority:
highest prioritymanual over-ride Permanent(3 sec. push)
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Muller SC 98.40 knx at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Muller SC 98.40 knx in the language / languages: English, German as an attachment in your email.
The manual is 3,96 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
