683949
2
Zoom out
Zoom in
Previous page
1/2
Next page
BA EA3632knx Hardware HM;DE,GB -23830- 2017.11V02 ED.doc
INSTRUCTION MANUAL INPUT/OUTPUT MODULE EA 36.32 KNX HUGO MÜLLER GMBH & CO KG, STURMBÜHLSTR. 145-149, 78054 VS-SCHWENNINGEN
SAFETY INSTRUCTIONS AND BASICS
EA 36.32 knx
Service:
Hugo Müller GmbH & Co KG
Sturmbühlstraße 145-149
D-78054 VS-Schwenningen
Germany
+49 7720 80836
www.hugo-mueller.de
Technical data
Safety instructions / Intended use
Power supply:
Bus current:
24 V DC (via KNX bus voltage)
< 10 mA
CAUTION! DANGER OF FIRE AND ELECTRIC SHOCK!
!!!Installation and assembly of electrical equipment must be carried out only by a skilled person!!!
Bus system:
KNX-TP/S
Connect only to suitable supply voltage [KNX bus voltage (nominal voltage 29V)].
Warranty void if housing opened by unauthorized person!
The electronic circuit is protected against a wide range of external influences. Incorrect operating may occur if external in fluences
exceed certain limits!
Installation and assembly of electrical equipment must be in accordance with national building, electrical and safety codes!
Defective devices / sensors have to be put out of service immediately!
Observe the regulations and instructions in the ZVEI/ZVEH handbook (building system technology). Especially the professional
installation of the bus lines and the professional installation and start -up of KNX devices must be observed!
The device fits for the particular use of the following tasks: monitoring of the air quality in building systems technology (schools,
offices, hotels, conference venue etc.), data transfer and regulation via bus system.
The device is intended for use in accordance with the defined technical data.
Operate the device exclusively in a dry room!
The device is not qualified for security relevant tasks such as emergency doors, fire protection equipment, fermenting cellar s etc.
Inputs:
3x binary Inputs (INPUT 1 / 2 / 3)
Input 2/3 can also be used as Input for external
temperature probes (PT1000 / Müller TF06). This
function requires use of both Inputs (2 and 3).
Outputs:
2x outputs (OUTPUT 1, OUTPUT 2)
- Can be configured as LED-driver (< 3 mA)
- Can be configured as Open-collector output
with the following specifications:
ext. supply voltage (U
max
) = 50 V DC
max. switching current (I
max
) = 80 mA
max. switching power (P
max
) = 200 mW
Voltage level on low signal = 0,5 V DC
Permitted ambient temperature:
-5°+45 °C
Housing:
self-extinguishing thermoplastic
Mounting:
Flush-mount (hollow-wall box)
Type of connection:
KNX bus terminal
Type of protection:
IP 20 to DIN EN 60529
Class of protection:
III when installed according to regulations
Inappropriate use / disposal
Input / Output Description (examples)
The device is not intended for use of unauthorized constructional alterations , repairs
and security relevant tasks.
The device is not intended for use in outdoor areas or wet rooms.
The device is not qualified for security relevant tasks. The intended use of the device is
only for comfort functions in home automation systems.
The inappropriate use of the device can cause damage to property and persons .
The device has to be disposed in an environmentally friendly manner according to the
current electrical codes!
Assembly
Disconnect device from power supply for wiring and installation
purposes! Check power supply is disconnected!
Attention! You have to check and consider the safety instructions above!
This device is suitable for mounting in a flush-mounting box.
Ensure that no dust gets inside of the device.
STEP 1: Connect the required inputs / outputs according to the schematics diagram.
STEP 2: Connect the KNX bus cable according to the color-coded connectors.
STEP 3: After wiring, press the programming buttonto set the device into
programming mode for addressing & configuration via ETS application.
STEP 4: Place / install device into the hollow-wall box.
Installation note: Make sure that no wires are pinched or squeezed when placing the device into the hollow-wall box.
Inputs configured as binary inputs
Outputs configured as LED drivers
Input 1 = binary input, Input 2/3 = temperature probe input
Outputs configured asopen-collector
Uext.:
Umax= 50 V DC
Imax = 80 mA
Pmax = 200 mW
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Muller EA 36.32 knx at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Muller EA 36.32 knx in the language / languages: English, German as an attachment in your email.

The manual is 0,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info