167884
4
Zoom out
Zoom in
Previous page
1/36
Next page
X1000D - amplifier owner's manual
4
Installation & Mounting
Any deviation from the connection specifications recommended may cause serious damage to the amplifier, spea-
kers and/or vehicle electrical system. Please double-check the connection before turning the system on.
1. Disconnect the vehicle’s negative battery connection.
2. Determine the mounting place for your MTX XTHUNDER amplifier. Keep in mind that there needs to be sufficient
air flow across the heatsink of the amplifier to ensure proper cooling. Mark the mounting holes of the amplifier and
drill the holes to mount your amplifier. Before drilling any holes make sure that all vehicle wires, gas lines, brake
lines, gastank etc. are clear and will not interfere with the installation. Mount your MTX XTHUNDER amplifier.
3. Run a positive power cable from the vehicle’s battery through the firewall using a grommet or firewall bushing to
avoid damage to the cable from sharp edges of the firewall. Run the cable through the interior of the vehicle and
connect the end to the amplifier’s +BATT terminal. Leave the cable disconnected from the battery.
Note : Use only proper gauge wire for both positive and negative connections for optimum performance.
4. Install a circuit breaker or fuse within 30cm of the battery. This effectively lowers the risk of severe damage to
you or your vehicle in case of a short circuit or accident. Make sure the circuitbreaker is switched off or the fuse is
taken out of the fuse holder untill all connections are made. Now connect your positive power cable to the positive
battery terminal of the battery
5. Find a good ground source on the vehicle’s chassis and remove the paint to reveal bare metal at the contact
point. Attach the ground wire to that contact point and connect the other end of the ground wire to the GND termi-
nal of your MTX XTHUNDER amplifier.
6. Connect a Remote Turn-on wire from your source unit to your MTX XTHUNDER amplifier’s Remote terminal. If
your source unit does not have a dedicated Remote Turn-on lead, you may connect to the source unit’s Power
Antenna lead.
7. Connect RCA cables from your source unit to your MTX XTHUNDER amplifier’s RCA input jacks. If RCA (low level)
output is not available, connect the included speaker (high level) connector to the speaker wires from the source
unit.
8. Connect your speakers to your MTX XTHUNDER amplifier’s speaker terminals using 4mm2 minimum speaker
cable.
9. Double-check all the previous installation steps, in particular, the wiring and component connections. If every-
thing is in order, reconnect the vehicle’s negative battery connection, switch your circuitbreaker on or place your
fuse in the fuse holder and begin adjusting your amplifier.
Note: Be sure that the Gain Level on the amplifier is turned all the way down (counter clockwise) before proceeding
with adjustments.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mtx audio x1000d at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mtx audio x1000d in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info