Manual MTD CubCadet serie 7000 (page 44 of 52) (English)

629099

Zoom out

Zoom in

1/52

ADDING ENGINE OIL

WARNING: Never overfill the engine

crankcase. The engine may overheat

and/or damage may result if the

crankcase is below the “ADD” mark or

over the “FULL” mark on the dipstick.

For best results, fill to the “FULL” mark

on the dipstick as opposed to adding a

given quantity of oil. Always check the

level on the dipstick before adding

more oil.

Refer to the LUBRICATION TABLE in the MAINTE-

NANCE SECTION of this manual to determine the

proper type of oil to add to the crankcase for the

conditions under which the engine will be operated.

• Place the tractor on a level surface and engage

the parking brake. Stop the tractor engine and

remove the ignition key.

• Clean the area around the oil filler cap to

prevent debris from entering the crankcase.

See Figure 53.

Figure 53

• Turn the oil filler cap counterclockwise to

unscrew from the oil fill tube.

• SLOWLY pour oil into the crankcase until the

oil level reaches the “FULL” mark on the

dipstick. Refer to Figure 52.

• Insert the oil fill cap into the oil fill tube and turn

clockwise until fully tightened. Reinsert the

dipstick into the dipstick tube and push firmly

into the tube.

IMPORTANT:

The oil fill cap and dipstick must

always be installed securely in place when the

engine is running. Severe engine damage could

result from failure to do so.

CHANGING THE ENGINE OIL AND FILTER

The engine oil and oil filter should be changed after

every 250 hours. Refer to the LUBRICATION

TABLE in the MAINTENANCE SECTION of this

manual for the quantity of oil needed, and to deter-

mine the proper type of oil to use for the conditions

under which the engine will be operated.

WARNING: Because the engine is run

prior to draining the oil, the engine may

be hot. Use caution to avoid burning

yourself on engine surfaces.

Run the engine for a few minutes to allow the oil in

the crankcase to warm up. Warm oil will flow more

freely and carry away more engine impurities. Use

care to avoid burns from hot oil. While the engine

oil is warm, proceed as follows:

• Place the tractor on a level surface and engage

the parking brake. Stop the tractor engine and

remove the ignition key.

• Clean around the base of the oil filter, the oil fill

cap, and the dipstick tube to prevent debris

from entering the crankcase.

• Remove the dipstick and oil fill cap from the

engine. Refer to Figure 51 and Figure 53.

• Locate the engine drain plug on the

right

of the

engine (See Figure 54). Place a suitable

container below the drain plug to collect the old

oil.

Figure 54

• Turn the drain plug counter-clockwise to

remove from the engine oil pan.

• Allow the old oil to completely drain from the

engine crankcase into the container below.

OIL FILL CAP

OIL FILL TUBE

OIL DRAIN PLUG

RT. FRAME RAIL

OIL PAN

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of MTD CubCadet serie 7000 in the language / languages: English as an attachment in your email.

The manual is 2,08 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of MTD CubCadet serie 7000

MTD CubCadet serie 7000 User Manual - German - 55 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

MTD CubCadet serie 7000 Manual

Product: