672421
11
Zoom out
Zoom in
Previous page
1/16
Next page
English Operating manual
8
Note
If required, turn the lower drive
shaft slightly until the square shaft
and the holder of the upper drive
shaft mesh.
Tighten screw handle (1)
on the shaft coupling clockwise.
Check that the lower drive shaft
is tight.
Removal
Turn screw handle (1) on the shaft
coupling (2) anti-clockwise
to open the shaft coupling.
Press release button (3) and
pull the lower drive shaft straight
out of the shaft coupling.
Adjusting the carrying
system (shoulder strap)
Fig. 3
Place harness over your
shoulders.
Close the catch on the abdominal
belt (1.). If required, readjust.
Adjust abdominal belt
to the correct width (2.).
Adjust shoulder belt
to the correct length (3.).
Latch the hook of the carrying
system into the holder on the unit
(4.) and adjust the attachment
pad to a comfortable length (5.).
Note
Clip A is used in an emergency
to release the appliance as quickly
as possible from the carrying
system.
To do this, pull the clip upwards.
Attaching the cutting
attachment cover
Fig. 4
Unscrew the screws (1) and
remove the clamp (2) from
the cutting attachment cover (3).
Place cutting attachment cover
(3) on the lower drive shaft (4)
and attach the clamp (2) with
the screws (1).
Do not tighten the screws yet!
Remove screw (5) from the gear-
box.
Attach holder (6) to the gearbox
with the screw (5).
Tighten the screws (1).
Attaching/removing
the line head
Attaching the line head
Fig. 5
If attached, remove cutters
and blade attachment parts
beforehand. See “Removing
the cutting blade”.
Push spacer (1) onto the drive
shaft (2). Align the 3 openings
in the spacer (3), the gearbox (4)
and the gear cover (5).
Note
If alignment is not correct, the line
head cannot be attached/removed!
Insert retaining bar (6) through
the openings (3, 4, 5) in order
to secure the gearbox.
While holding the retaining
bar (6), turn the line head (7)
anti-clockwise (to the left)
onto the drive shaft.
Tighten line head firmly!
Note
Ensure that the line head (7)
is seated correctly on the spacer
(1), i.e. centred and resting flat!
Remove retaining bar from
the gear head.
Remove the line head
Fig. 6
Align the openings (3, 4, 5). Insert
retaining bar (6) through the
openings and hold in position.
Unscrew line head (7) clockwise
(to the right) off the drive shaft.
Attaching/removing the
cutting blade (depending
on model)
Attaching the cutting blade
Fig. 7
If attached, remove the line head
beforehand. See “Attaching/re-
moving the line head”.
Note
When attaching the cutting blade
for the first time, remove the blade
attachment parts (blade holder (8),
retaining bell (9), nut (10))
if attached. See “Removing
the cutting blade”.
Push spacer (1) onto the drive
shaft (2). Align the 3 openings
in the spacer (3), the gearbox (4)
and the gear cover (5) (Fig. 5).
Note
If alignment is not correct,
the cutting blade cannot
be attached/removed!
Insert retaining bar (6) through
the openings (3, 4, 5) in order
to secure the gearbox.
While holding the retaining bar
(6), attach the cutting blade (7)
with
blade holder (8), retaining
bell (9) and nut (10)
as follows:
Push cutting blade (7) onto
drive shaft (2) and centre
on the spacer (1).
Note
Ensure that the cutting blade (7)
is seated correctly on the spacer
(1), i.e. centred and resting flat!
Attach blade holder (8), retai-
ning bell (9) and nut (10).
Ensure that the blade holder is
seated correctly in the toothing!
Tighten nut firmly anti-clock-
wise (to the left) – tightening
torque 37 Nm.
Note
Before tightening, check again
that the cutting blade is seated
correctly.
If you do not have a torque
wrench, tighten the nut firmly by
hand. Then tighten the nut anti-
clockwise (to the left) another
half turn using a ring spanner.
Remove retaining bar from
the gear head.
Remove guard (if fitted) from
the cutting blade.
Removing the cutting blade
Fig. 8
Attach guard (if available)
to the cutting blade.
Align the openings (3, 4, 5).
Insert retaining bar (6) through
the openings and hold in position.
Unscrew nut clockwise (to the
right).
Remove cutting blade (7), blade
holder (8) and retaining bell (9)
(Fig. 7).
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for MTD BC43 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of MTD BC43 in the language / languages: English as an attachment in your email.

The manual is 2,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of MTD BC43

MTD BC43 User Manual - German - 18 pages

MTD BC43 User Manual - Dutch - 17 pages

MTD BC43 User Manual - French - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info